ST92F150JDV1QC STMicroelectronics, ST92F150JDV1QC Datasheet - Page 155

• Manufacturer Part Number: ST92F150JDV1QC
• Description: IC MCU 128K FLASH 100-PQFP
• Manufacturer: STMicroelectronics
• Series: ST9r

Specifications of ST92F150JDV1QC

• Core Processor: ST9
• Core Size: 8/16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 77
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-QFP
• Processor Series: ST92F15x
• Core: ST9
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 6 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST92F150-EPB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit x 10 bit
• Case: QFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2137

INPUT/OUTPUT BIT CONFIGURATION (Cont’d)
When Px.n is programmed as an Output:
(Figure
– The Output Buffer is turned on in an Open-drain
– The data stored in the Output Master Latch is
When Px.n is programmed as Bidirectional:
(Figure
– The Output Buffer is turned on in an Open-Drain
– The data present on the I/O pin is sampled into
– The data stored in the Output Master Latch is
WARNING: Due to the fact that in bidirectional
mode the external pin is read instead of the output
latch, particular care must be taken with arithme-
tic/logic and Boolean instructions performed on a
bidirectional port pin.
These instructions use a read-modify-write se-
quence, and the result written in the port register
depends on the logical level present on the exter-
nal pin.
This may bring unwanted modifications to the port
output register content.
For example:
Port register content, 0Fh
external port value, 03h
(Bits 3 and 2 are externally forced to 0)
A bset instruction on bit 7 will return:
Port register content, 83h
external port value, 83h
(Bits 3 and 2 have been cleared).
To avoid this situation, it is suggested that all oper-
ations on a port, using at least one bit in bidirec-
tional mode, are performed on a copy of the port
register, then transferring the result with a load in-
struction to the I/O port.
When Px.n is programmed as a digital Alter-
nate Function Output:
(Figure
– The Output Buffer is turned on in an Open-Drain
or Push-pull configuration.
copied both into the Input Latch and into the Out-
put Slave Latch, driving the I/O pin, at the end of
the execution of the instruction.
or Weak Pull-up configuration (except when dis-
abled in hardware).
the Input Latch at the beginning of the execution
of the instruction.
copied into the Output Slave Latch, driving the I/
O pin, at the end of the execution of the instruc-
tion.
or Push-Pull configuration.
83)
84)
85)
– The data present on the I/O pin is sampled into
– The signal from an on-chip function is allowed to
Figure 84. Bidirectional Configuration
n
n
Figure 85. Alternate Function Configuration
n
n
n
n
n
n
the Input Latch at the beginning of the execution
of the instruction.
load the Output Slave Latch driving the I/O pin.
Signal timing is under control of the alternate
function. If no alternate function is connected to
Px.n, the I/O pin is driven to a high level when in
Push-Pull configuration, and to a high imped-
ance state when in open drain configuration.
WEAK PULL-UP
OPEN DRAIN
OPEN DRAIN
PUSH-PULL
PERIPHERAL
OUTPUT MASTER LATCH
OUTPUT SLAVE LATCH
OUTPUT
OUTPUT SLAVE LATCH
FROM
ST92F124/F150/F250 - I/O PORTS
INTERNAL DATA BUS
INTERNAL DATA BUS
I/O PIN
I/O PIN
INPUT LATCH
INPUT LATCH
(or Schmitt Trigger)
(or Schmitt Trigger)
TO PERIPHERAL
INTERRUPTS
INPUTS AND
TO PERIPHERAL
INTERRUPTS
INPUTS AND
TTL
TTL
155/429
9