ST92F150JDV1QC STMicroelectronics, ST92F150JDV1QC Datasheet - Page 163

• Manufacturer Part Number: ST92F150JDV1QC
• Description: IC MCU 128K FLASH 100-PQFP
• Manufacturer: STMicroelectronics
• Series: ST9r

Specifications of ST92F150JDV1QC

• Core Processor: ST9
• Core Size: 8/16-Bit
• Speed: 24MHz
• Connectivity: CAN, I²C, LIN, SCI, SPI
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 77
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 6K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-QFP
• Processor Series: ST92F15x
• Core: ST9
• Data Bus Width: 8 bit, 16 bit
• Data Ram Size: 6 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 80
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST92F150-EPB
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit x 10 bit
• Case: QFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2137

TIMER/WATCHDOG (Cont’d)
Bit 3 = INEN: Input Enable.
This bit is set and cleared by software.
0: Disable input section
1: Enable input section
Bit 2 = OUTMD: Output Mode.
This bit is set and cleared by software.
0: The output is toggled at every End of Count
1: The value of the WROUT bit is transferred to the
Bit 1 = WROUT: Write Out.
The status of this bit is transferred to the Output
pin when OUTMD is set; it is user definable to al-
low PWM output (on Reset WROUT is set).
Bit 0 = OUTEN: Output Enable bit.
This bit is set and cleared by software.
0: Disable output
1: Enable output
WAIT CONTROL REGISTER (WCR)
R252 - Read/Write
Register Page: 0
Reset value: 0111 1111 (7Fh)
Bit 6 = WDGEN: Watchdog Enable (active low).
Resetting this bit via software enters the Watch-
dog mode. Once reset, it cannot be set any more
7
x
output pin on every End Of Count if OUTEN=1.
WDGEN
x
x
x
x
x
0
x
by the user program. At System Reset, the Watch-
dog mode is disabled.
Note: This bit is ignored if the Hardware Watchdog
option is enabled by pin HW0SW1 (if available).
EXTERNAL INTERRUPT VECTOR REGISTER
(EIVR)
R246 - Read/Write
Register Page: 0
Reset value: xxxx 0110 (x6h)
Bit 2 = TLIS: Top Level Input Selection.
This bit is set and cleared by software.
0: Watchdog End of Count is TL interrupt source
1: NMI is TL interrupt source
Bit 1 = IA0S: Interrupt Channel A0 Selection.
This bit is set and cleared by software.
0: Watchdog End of Count is INTA0 source
1: External Interrupt pin is INTA0 source
Warning: To avoid spurious interrupt requests,
the IA0S bit should be accessed only when the in-
terrupt logic is disabled (i.e. after the DI instruc-
tion). It is also necessary to clear any possible in-
terrupt pending requests on channel A0 before en-
abling this interrupt channel. A delay instruction
(e.g. a NOP instruction) must be inserted between
the reset of the interrupt pending bit and the IA0S
write instruction.
Other bits are described in the Interrupt section.
7
x
x
x
TIMER/WATCHDOG (WDT)
x
x
TLIS IA0S
163/429
0
x
9