MC68HC908GP32CB Freescale Semiconductor, MC68HC908GP32CB Datasheet - Page 182

• Manufacturer Part Number: MC68HC908GP32CB
• Description: IC MCU 32K FLASH 8MHZ 42-SDIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908GP32CB

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 33
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• For Use With: M68EVB908GP32 - BOARD EVALUATION FOR HC908GP32
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Serial Peripheral Interface Module (SPI)
to accept new data. Write to the transmit data register only when the SPTE bit is high.
the timing associated with doing back-to-back transmissions with the SPI (SPSCK has CPHA: CPOL =
1:0).
The transmit data buffer allows back-to-back transmissions without the slave precisely timing its writes
between transmissions as in a system with a single data buffer. Also, if no new data is written to the data
buffer, the last value contained in the shift register is the next data word to be transmitted.
For an idle master or idle slave that has no data loaded into its transmit buffer, the SPTE is set again no
more than two bus cycles after the transmit buffer empties into the shift register. This allows the user to
queue up a 16-bit value to send. For an already active slave, the load of the shift register cannot occur
until the transmission is completed. This implies that a back-to-back write to the transmit data register is
not possible. The SPTE indicates when the next write can occur.
15.7 Error Conditions
The following flags signal SPI error conditions:
182
•
•
Overflow (OVRF) — Failing to read the SPI data register before the next full byte enters the shift
register sets the OVRF bit. The new byte does not transfer to the receive data register, and the
unread byte still can be read. OVRF is in the SPI status and control register.
Mode fault error (MODF) — The MODF bit indicates that the voltage on the slave select pin (SS)
is inconsistent with the mode of the SPI. MODF is in the SPI status and control register.
CPHA:CPOL = 1:0
WRITE TO SPDR
1
2
3
4 FIRST INCOMING BYTE TRANSFERS FROM SHIFT
5
6 CPU READS SPSCR WITH SPRF BIT SET.
READ SPSCR
CPU WRITES BYTE 1 TO SPDR, CLEARING SPTE BIT.
BYTE 1 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
CPU WRITES BYTE 2 TO SPDR, QUEUEING BYTE 2
AND CLEARING SPTE BIT.
REGISTER TO RECEIVE DATA REGISTER, SETTING
SPRF BIT.
BYTE 2 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
READ SPDR
SPSCK
SPTE
SPRF
MOSI
1
Figure 15-8. SPRF/SPTE CPU Interrupt Timing
MC68HC908GP32 Data Sheet, Rev. 10
MSB BIT
BYTE 1
2
6
BIT
5
3
BIT
4
BIT
3
BIT
2
BIT
1
10
11 CPU READS SPSCR WITH SPRF BIT SET.
12 CPU READS SPDR, CLEARING SPRF BIT.
7 CPU READS SPDR, CLEARING SPRF BIT.
8
9
LSB MSB BIT
5
4
CPU WRITES BYTE 3 TO SPDR, QUEUEING BYTE
3 AND CLEARING SPTE BIT.
SECOND INCOMING BYTE TRANSFERS FROM SHIFT
REGISTER TO RECEIVE DATA REGISTER, SETTING
SPRF BIT.
BYTE 3 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
BYTE 2
6
6
7
BIT
5
8
BIT
4
BIT
3
BIT
2
BIT
1
LSB MSB BIT
10
9
BYTE 3
11
Freescale Semiconductor
6
12
Figure 15-8
BIT
5
BIT
4
shows