MC68HC908GP32CB Freescale Semiconductor, MC68HC908GP32CB Datasheet - Page 44

• Manufacturer Part Number: MC68HC908GP32CB
• Description: IC MCU 32K FLASH 8MHZ 42-SDIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908GP32CB

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 33
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• For Use With: M68EVB908GP32 - BOARD EVALUATION FOR HC908GP32
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Memory
When the FLBPR is programmed with all 0’s, the entire memory is protected from being programmed and
erased. When all the bits are erased (all 1’s), the entire memory is accessible for program and erase.
When bits within the FLBPR are programmed, they lock a block of memory, address ranges as shown in
2.6.6.1 FLASH Block Protect
erase or program of the FLBPR or the protected block of FLASH memory is prohibited. Mass erase is
disabled whenever any block is protected (FLBPR does not equal $FF). The presence of a V
IRQ pin will bypass the block protection so that all of the memory included in the block protect register is
open for program and erase operations.
2.6.6.1 FLASH Block Protect Register
The FLASH block protect register (FLBPR) is implemented as a byte within the FLASH memory, and
therefore can only be written during a programming sequence of the FLASH memory. The value in this
register determines the starting location of the protected range within the FLASH memory.
BPR[7:0] — FLASH Block Protect Bits
44
These eight bits represent bits [14:7] of a 16-bit memory address.
Bit-15 is 1 and bits [6:0] are 0s.
The resultant 16-bit address is used for specifying the start address of the FLASH memory for block
protection. The FLASH is protected from this start address to the end of FLASH memory, at $FFFF.
With this mechanism, the protect start address can be XX00 and XX80 (128 bytes page boundaries)
within the FLASH memory.
Address:
The FLASH block protect register is not protected with special hardware or
software. Therefore, if this page is not protected by FLBPR the register is
erased by either a page or mass erase operation.
Reset:
Read:
Write:
Start address of FLASH block protect
U = Unaffected by reset. Initial value from factory is 1.
Write to this register is by a programming sequence to the FLASH memory.
$FF7E
BPR7
Bit 7
U
Figure 2-5. FLASH Block Protect Register (FLBPR)
Figure 2-6. FLASH Block Protect Start Address
Register. Once the FLBPR is programmed with a value other than $FF, any
BPR6
U
6
MC68HC908GP32 Data Sheet, Rev. 10
BPR5
U
5
1
NOTE
BPR4
U
4
FLBPR value
16-bit memory address
BPR3
U
3
BPR2
0 0 0 0 0 0 0
U
2
BPR1
U
1
Freescale Semiconductor
BPR0
Bit 0
U
TST
on the