C8051F336-GMR Silicon Laboratories Inc, C8051F336-GMR Datasheet - Page 104

• Manufacturer Part Number: C8051F336-GMR
• Description: Microcontrollers (MCU) 16KB 10ADC 10DAC 768Ram MCU Lead Free
• Manufacturer: Silicon Laboratories Inc

Specifications of C8051F336-GMR

• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 16 KB
• Data Ram Size: 768 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: QFN-20
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F336DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• On-chip Dac: 10 bit
• Package: 20QFN
• Device Core: 8051
• Family Name: C8051F336
• Maximum Speed: 25 MHz
• Ram Size: 768 Byte
• Operating Temperature: -40 to 85 °C
• Lead Free Status / Rohs Status: Details

C8051F336/7/8/9
17.5. Comparator0 Reset
Comparator0 can be configured as a reset source by writing a ‘1’ to the C0RSEF flag (RSTSRC.5).
Comparator0 should be enabled and allowed to settle prior to writing to C0RSEF to prevent any turn-on
chatter on the output from generating an unwanted reset. The Comparator0 reset is active-low: if the non-
inverting input voltage (on CP0+) is less than the inverting input voltage (on CP0-), the device is put into
the reset state. After a Comparator0 reset, the C0RSEF flag (RSTSRC.5) will read ‘1’ signifying
Comparator0 as the reset source; otherwise, this bit reads ‘0’. The state of the RST pin is unaffected by
this reset.
17.6. PCA Watchdog Timer Reset
The programmable Watchdog Timer (WDT) function of the Programmable Counter Array (PCA) can be
used to prevent software from running out of control during a system malfunction. The PCA WDT function
can be enabled or disabled by software as described in
page
prevents user software from updating the WDT, a reset is generated and the WDTRSF bit (RSTSRC.5) is
set to ‘1’. The state of the RST pin is unaffected by this reset.
17.7. Flash Error Reset
If a Flash read/write/erase or program read targets an illegal address, a system reset is generated. This
may occur due to any of the following:
The FERROR bit (RSTSRC.6) is set following a Flash error reset. The state of the RST pin is unaffected by
this reset.
17.8. Software Reset
Software may force a reset by writing a ‘1’ to the SWRSF bit (RSTSRC.4). The SWRSF bit will read ‘1’ fol-
lowing a software forced reset. The state of the RST pin is unaffected by this reset.
104
A Flash write or erase is attempted above user code space. This occurs when PSWE is set to ‘1’ and a
MOVX write operation targets an address above address 0x3DFF.
A Flash read is attempted above user code space. This occurs when a MOVC operation targets an
address above address 0x3DFF.
A Program read is attempted above user code space. This occurs when user code attempts to branch
to an address above 0x3DFF.
A Flash read, write or erase attempt is restricted due to a Flash security setting (see
“16.3. Security Options” on page
213; the WDT is enabled and clocked by SYSCLK / 12 following any reset. If a system malfunction
93).
Rev.1.0
Section “25.4. Watchdog Timer Mode” on
Section