LPC2420_60 NXP Semiconductors, LPC2420_60 Datasheet - Page 17

no-image

LPC2420_60

Manufacturer Part Number
LPC2420_60
Description
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer
NXP Semiconductors
Datasheet
NXP Semiconductors
Table 4.
LPC2420_60
Product data sheet
Symbol
P2[3]/PWM1[4]/
DCD1/
PIPESTAT2
P2[4]/PWM1[5]/
DSR1/
TRACESYNC
P2[5]/PWM1[6]/
DTR1/
TRACEPKT0
P2[6]/PCAP1[0]/
RI1/TRACEPKT1
P2[7]/RD2/
RTS1/
TRACEPKT2
P2[9]/
USB_CONNECT1/
RXD2/
EXTIN0
P2[10]/EINT0
P2[11]/EINT1/
MCIDAT1/
I2STX_CLK
P2[8]/TD2/
TXD2/
TRACEPKT3
Pin description
Pin
144
142
140
138
136
134
132
110
108
[6]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[6]
…continued
Ball
E16
D17
F16
E17
G16
H15
H16
N15
T17
[1]
[6]
[1]
[1]
[1]
[1]
[1]
[6]
[1]
All information provided in this document is subject to legal disclaimers.
Type
I/O
O
I
O
I/O
O
I
O
I/O
O
O
O
I/O
I
I
O
I/O
I
O
O
I/O
O
O
O
I/O
O
I
I
I/O
I
I/O
I
I/O
I/O
Rev. 6.1 — 22 September 2011
Description
P2[3] — General purpose digital input/output pin.
PWM1[4] — Pulse Width Modulator 1, channel 4 output.
DCD1 — Data Carrier Detect input for UART1.
PIPESTAT2 — Pipeline Status, bit 2.
P2[4] — General purpose digital input/output pin.
PWM1[5] — Pulse Width Modulator 1, channel 5 output.
DSR1 — Data Set Ready input for UART1.
TRACESYNC — Trace Synchronization.
P2[5] — General purpose digital input/output pin.
PWM1[6] — Pulse Width Modulator 1, channel 6 output.
DTR1 — Data Terminal Ready output for UART1.
TRACEPKT0 — Trace Packet, bit 0.
P2[6] — General purpose digital input/output pin.
PCAP1[0] — Capture input for PWM1, channel 0.
RI1 — Ring Indicator input for UART1.
TRACEPKT1 — Trace Packet, bit 1.
P2[7] — General purpose digital input/output pin.
RD2 — CAN2 receiver input (LPC2460 only).
RTS1 — Request to Send output for UART1.
TRACEPKT2 — Trace Packet, bit 2.
P2[8] — General purpose digital input/output pin.
TD2 — CAN2 transmitter output (LPC2460 only).
TXD2 — Transmitter output for UART2.
TRACEPKT3 — Trace Packet, bit 3.
P2[9] — General purpose digital input/output pin.
USB_CONNECT1 — USB1 SoftConnect control. Signal used to
switch an external 1.5 k resistor under the software control. Used
with the SoftConnect USB feature.
RXD2 — Receiver input for UART2.
EXTIN0 — External Trigger Input.
P2[10] — General purpose digital input/output pin.
Note: LOW on this pin while RESET is LOW forces on-chip
bootloader to take over control of the part after a reset.
EINT0 — External interrupt 0 input.
P2[11] — General purpose digital input/output pin.
EINT1 — External interrupt 1 input.
MCIDAT1 — Data line 1 for SD/MMC interface.
I2STX_CLK — Transmit Clock. It is driven by the master and received
by the slave. Corresponds to the signal SCK in the I
specification.
Flashless 16-bit/32-bit microcontroller
LPC2420/2460
© NXP B.V. 2011. All rights reserved.
2
S-bus
17 of 86

Related parts for LPC2420_60