AT32AP7001-ALUT Atmel, AT32AP7001-ALUT Datasheet - Page 367

• Manufacturer Part Number: AT32AP7001-ALUT
• Description: IC MCU 32BIT AVR32 208-LQFP
• Manufacturer: Atmel
• Series: AVR®32 AP7r

Specifications of AT32AP7001-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: EBI/EMI, I²C, MMC, PS2, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, I²C, POR, PWM, WDT
• Number Of I /o: 90
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: D/A 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-LQFP
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: EBI, ISI, MCI, PS2, SPI, TWI, USB
• Maximum Clock Frequency: 150 MHz
• Number Of Programmable I/os: 90
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Dac: 16 bit, 1 Channel
• Package: 208PQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 150 MHz
• Operating Supply Voltage: 1.8 V
• For Use With: ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMRATNGW100 - KIT AVR32 NETWORK GATEWAYATSTK1000 - KIT STARTER FOR AVR32AP7000
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details

24.9.3
Name:
Access Type:
Offset:
Reset value:
• PERIOD: Receive Period Divider Selection
This field selects the divider to apply to the selected Receive Clock in order to generate a new Frame Sync Signal. If 0, no
PERIOD signal is generated. If not 0, a PERIOD signal is generated each 2 x (PERIOD+1) Receive Clock.
• STTDLY: Receive Start Delay
If STTDLY is not 0, a delay of STTDLY clock cycles is inserted between the start event and the actual start of reception.
When the Receiver is programmed to start synchronously with the Transmitter, the delay is also applied.
Note: It is very important that STTDLY be set carefully. If STTDLY must be set, it should be done in relation to TAG
(Receive Sync Data) reception.
• STOP: Receive Stop Selection
0: After completion of a data transfer when starting with a Compare 0, the receiver stops the data transfer and waits for a
new compare 0.
1: After starting a receive with a Compare 0, the receiver operates in a continuous mode until a Compare 1 is detected.
• START: Receive Start Selection
32015G–AVR32–09/09
0x9-0xF
START
0x0
0x1
0x2
0x3
0x4
0x5
0x6
0x7
0x8
31
23
15
–
7
Receive Clock Mode Register
CKG
Continuous, as soon as the receiver is enabled, and immediately after the end of
transfer of the previous data.
Transmit start
Detection of a low level on RX_FRAME_SYNC signal
Detection of a high level on RX_FRAME_SYNC signal
Detection of a falling edge on RX_FRAME_SYNC signal
Detection of a rising edge on RX_FRAME_SYNC signal
Detection of any level change on RX_FRAME_SYNC signal
Detection of any edge on RX_FRAME_SYNC signal
Compare 0
Reserved
Receive Start
30
22
14
0x10
0x00000000
–
6
CKI
29
21
13
–
5
RCMR
Read/Write
STOP
28
20
12
4
PERIOD
STTDLY
CKO
27
19
11
3
26
18
10
2
START
AT32AP7001
25
17
9
1
CKS
24
16
8
0
367