AT32AP7001-ALUT Atmel, AT32AP7001-ALUT Datasheet - Page 607

• Manufacturer Part Number: AT32AP7001-ALUT
• Description: IC MCU 32BIT AVR32 208-LQFP
• Manufacturer: Atmel
• Series: AVR®32 AP7r

Specifications of AT32AP7001-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: EBI/EMI, I²C, MMC, PS2, SPI, SSC, UART/USART, USB
• Peripherals: AC'97, DMA, I²C, POR, PWM, WDT
• Number Of I /o: 90
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: D/A 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-LQFP
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: EBI, ISI, MCI, PS2, SPI, TWI, USB
• Maximum Clock Frequency: 150 MHz
• Number Of Programmable I/os: 90
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Dac: 16 bit, 1 Channel
• Package: 208PQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 150 MHz
• Operating Supply Voltage: 1.8 V
• For Use With: ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMRATNGW100 - KIT AVR32 NETWORK GATEWAYATSTK1000 - KIT STARTER FOR AVR32AP7000
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details

32.6.4
32015G–AVR32–09/09
Endpoint Configuration
Figure 32-3. Control Read and Write Sequences
A status IN or OUT transaction is identical to a data IN or OUT transaction.
The endpoint 0 is always a control endpoint, it must be programmed and active in order to be
enabled when the End Of Reset interrupt occurs.
To configure the endpoints:
• Fill the configuration register (EPTCFG) with the endpoint size, direction (IN or OUT), type
• Fill the number of transactions (NB_TRANS) for isochronous endpoints.
Note: For control endpoints the direction has no effect.
• Verify that the EPT_MAPD flag is set. This flag is set if the endpoint size and the number of
• Configure control flags of the endpoint and enable it in EPTCTLENBx according to
Control endpoints can generate interrupts and use only 1 bank.
All endpoints (except endpoint 0) can be configured either as Bulk, Interrupt or Isochronous. See
Table 32-1. USBA Endpoint
The maximum packet size they can accept corresponds to the maximum endpoint size.
Note: The endpoint size of 1024 is reserved for isochronous endpoints.
The size of the DPRAM is 4 KB. The DPR is shared by all active endpoints. The memory size
required by the active endpoints must not exceed the size of the DPRAM.
(CTRL, Bulk, IT, ISO) and the number of banks.
banks are correct compared to the FIFO maximum capacity and the maximum number of
allowed banks.
Endpoint Control Register” on page
Control Write
Control Read
No Data
Control
Setup Stage
Setup Stage
Setup Stage
Setup TX
Setup TX
Setup TX
Description.
Status Stage
Status IN TX
Data OUT TX
Data IN TX
658.
Data Stage
Data Stage
Data OUT TX
Data IN TX
AT32AP7001
Status OUT TX
Status Stage
Status IN TX
Status Stage
”USBA
607