AT91SAM7S128C-MU Atmel, AT91SAM7S128C-MU Datasheet - Page 66

• Manufacturer Part Number: AT91SAM7S128C-MU
• Description: IC MCU ARM7 128K FLASH 64-QFN
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7S128C-MU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VQFN Exposed Pad, 64-HVQFN, 64-SQFN, 64-DHVQFN
• Core: ARM7TDMI
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7S-EK - KIT EVAL FOR ARM AT91SAM7S
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: AT91SAM7S128-MU; AT91SAM7S128-MU

13.3.5
13.3.6
66
AT91SAM7S Series Preliminary
Reset State Priorities
Reset Controller Status Register
The Reset State Manager manages the following priorities between the different reset sources,
given in descending order:
Particular cases are listed below:
The Reset Controller status register (RSTC_SR) provides several status fields:
• Power-up Reset
• Brownout Reset
• Watchdog Reset
• Software Reset
• User Reset
• When in User Reset:
• When in Software Reset:
• When in Watchdog Reset:
• RSTTYP field: This field gives the type of the last reset, as explained in previous sections.
• SRCMP bit: This field indicates that a Software Reset Command is in progress and that no
• NRSTL bit: The NRSTL bit of the Status Register gives the level of the NRST pin sampled on
• URSTS bit: A high-to-low transition of the NRST pin sets the URSTS bit of the RSTC_SR
• BODSTS bit: This bit indicates a brownout detection when the brownout reset is disabled
further software reset should be performed until the end of the current one. This bit is
automatically cleared at the end of the current software reset.
each MCK rising edge.
register. This transition is also detected on the Master Clock (MCK) rising edge (see
13-9). If the User Reset is disabled (URSTEN = 0) and if the interruption is enabled by the
URSTIEN bit in the RSTC_MR register, the URSTS bit triggers an interrupt. Reading the
RSTC_SR status register resets the URSTS bit and clears the interrupt.
(bod_rst_en = 0). It triggers an interrupt if the bit BODIEN in the RSTC_MR register enables
the interrupt. Reading the RSTC_SR register resets the BODSTS bit and clears the interrupt.
– A watchdog event is impossible because the Watchdog Timer is being reset by the
– A software reset is impossible, since the processor reset is being activated.
– A watchdog event has priority over the current state.
– The NRST has no effect.
– The processor reset is active and so a Software Reset cannot be programmed.
– A User Reset cannot be entered.
proc_nreset signal.
6175K–ATARM–30-Aug-10
Figure