PIC18F87J72-I/PT Microchip Technology, PIC18F87J72-I/PT Datasheet - Page 39

• Manufacturer Part Number: PIC18F87J72-I/PT
• Description: IC PIC MCU 8BIT 14KB FLSH 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F87J72-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 80-TQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: SPI, USART, SPI, I2C
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14
• Controller Family/series: PIC18F
• No. Of I/o's: 51
• Ram Memory Size: 3923Byte
• Cpu Speed: 48MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

4.3
The power-managed Sleep mode is identical to the leg-
acy Sleep mode offered in all other PIC devices. It is
entered by clearing the IDLEN bit (the default state on
device Reset) and executing the SLEEP instruction.
This shuts down the selected oscillator (Figure 4-5). All
clock source status bits are cleared.
Entering the Sleep mode from any other mode does not
require a clock switch. This is because no clocks are
needed once the controller has entered Sleep. If the
WDT is selected, the INTRC source will continue to
operate. If the Timer1 oscillator is enabled, it will also
continue to run.
When a wake event occurs in Sleep mode (by interrupt,
Reset or WDT time-out), the device will not be clocked
until the clock source selected by the SCS<1:0> bits
becomes ready (see Figure 4-6), or it will be clocked
from the internal oscillator if either the Two-Speed
Start-up or the Fail-Safe Clock Monitor is enabled (see
Section 26.0 “Special Features of the CPU”). In
either case, the OSTS bit is set when the primary clock
is providing the device clocks. The IDLEN and SCS bits
are not affected by the wake-up.
FIGURE 4-5:
FIGURE 4-6:
 2010 Microchip Technology Inc.
Peripheral
Program
Counter
OSC1
Sleep
Clock
Clock
CPU
Note 1: T
CPU Clock
PLL Clock
Peripheral
Program
Sleep Mode
Counter
Output
OSC1
Clock
Q1
OST
Q2
PC
= 1024 T
Q3
Wake Event
Q4
TRANSITION TIMING FOR ENTRY TO SLEEP MODE
TRANSITION TIMING FOR WAKE FROM SLEEP (HSPLL)
OSC
Q1
; T
Q1
PLL
T
OST (1)
= 2 ms (approx). These intervals are not shown to scale.
PC
T
PLL (1)
OSTS Bit Set
Preliminary
Q2 Q3 Q4 Q1 Q2
PC + 2
PIC18F87J72 FAMILY
4.4
The Idle modes allow the controller’s CPU to be
selectively shut down while the peripherals continue to
operate. Selecting a particular Idle mode allows users
to further manage power consumption.
If the IDLEN bit is set to a ‘1’ when a SLEEP instruction is
executed, the peripherals will be clocked from the clock
source selected using the SCS<1:0> bits; however, the
CPU will not be clocked. The clock source status bits are
not affected. Setting IDLEN and executing a SLEEP
instruction provides a quick method of switching from a
given Run mode to its corresponding Idle mode.
If the WDT is selected, the INTRC source will continue
to operate. If the Timer1 oscillator is enabled, it will also
continue to run.
Since the CPU is not executing instructions, the only
exits from any of the Idle modes are by interrupt, WDT
time-out or a Reset. When a wake event occurs, CPU
execution is delayed by an interval of T
(parameter 38, Table 29-11) while it becomes ready to
execute code. When the CPU begins executing code,
it resumes with the same clock source for the current
Idle mode. For example, when waking from RC_IDLE
mode, the internal oscillator block will clock the CPU
and peripherals (in other words, RC_RUN mode). The
IDLEN and SCS bits are not affected by the wake-up.
While in any Idle mode or the Sleep mode, a WDT
time-out will result in a WDT wake-up to the Run mode
currently specified by the SCS<1:0> bits.
PC + 2
Idle Modes
Q3 Q4 Q1 Q2
PC + 4
Q3 Q4
Q1 Q2 Q3 Q4
PC + 6
DS39979A-page 39
CSD