DSPD56367PV150 Freescale Semiconductor, DSPD56367PV150 Datasheet - Page 16

• Manufacturer Part Number: DSPD56367PV150
• Manufacturer: Freescale Semiconductor

Specifications of DSPD56367PV150

• Device Core Size: 24b
• Format: Fixed Point
• Clock Freq (max): 150MHz
• Mips: 150
• Device Input Clock Speed: 150MHz
• Ram Size: 69KB
• Program Memory Size: 120KB
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (min): 1.71/3.14V
• Operating Supply Voltage (max): 1.89/3.46V
• Operating Temp Range: -40C to 95C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Lead Free Status / Rohs Status: Not Compliant

Serial Host Interface
2-12
Signal
HREQ
Name
MOSI
HA0
HA2
SS
Input or
Input or
Signal
Output
Output
Type
Input
Input
Input
State During
Tri-Stated
Tri-Stated
Tri-Stated
Reset
Table 2-10 Serial Host Interface Signals (continued)
SPI Master-Out-Slave-In—When the SPI is configured as a master, MOSI is the
master data output line. The MOSI signal is used in conjunction with the MISO
signal for transmitting and receiving serial data. MOSI is the slave data input line
when the SPI is configured as a slave. This signal is a Schmitt-trigger input when
configured for the SPI Slave mode.
I
the I
the slave device address. HA0 is ignored when configured for the I
This signal is tri-stated during hardware, software, and individual reset. Thus, there
is no need for an external pull-up in this state.
This input is 3.3V tolerant.
SPI Slave Select—This signal is an active low Schmitt-trigger input when
configured for the SPI mode. When configured for the SPI Slave mode, this signal
is used to enable the SPI slave for transfer. When configured for the SPI master
mode, this signal should be kept deasserted (pulled high). If it is asserted while
configured as SPI master, a bus error condition is flagged. If SS is deasserted, the
SHI ignores SCK clocks and keeps the MISO output signal in the high-impedance
state.
I
the I
form the slave device address. HA2 is ignored in the I
This signal is tri-stated during hardware, software, and individual reset. Thus, there
is no need for an external pull-up in this state.
This input is 3.3V tolerant.
Host Request—This signal is an active low Schmitt-trigger input when configured
for the master mode but an active low output when configured for the slave mode.
When configured for the slave mode, HREQ is asserted to indicate that the SHI is
ready for the next data word transfer and deasserted at the first clock pulse of the
new data word transfer. When configured for the master mode, HREQ is an input.
When asserted by the external slave device, it will trigger the start of the data word
transfer by the master. After finishing the data word transfer, the master will await
the next assertion of HREQ to proceed to the next transfer.
This signal is tri-stated during hardware, software, personal reset, or when the
HREQ1–HREQ0 bits in the HCSR are cleared. There is no need for external pull-up
in this state.
This input is 3.3V tolerant.
2
2
C Slave Address 0—This signal uses a Schmitt-trigger input when configured for
C Slave Address 2—This signal uses a Schmitt-trigger input when configured for
DSP56367 Technical Data, Rev. 2.1
2
2
C mode. When configured for I
C mode. When configured for the I
Signal Description
2
C slave mode, the HA0 signal is used to form
2
C Slave mode, the HA2 signal is used to
2
C master mode.
Freescale Semiconductor
2
C master mode.