ST7232AK2-Auto STMicroelectronics, ST7232AK2-Auto Datasheet - Page 66
ST7232AK2-Auto
Manufacturer Part Number
ST7232AK2-Auto
Description
8-bit MCU for automotive, 16 Kbyte Flash, 10-bit ADC, 4 timers, SPI, SCI
Manufacturer
STMicroelectronics
Datasheet
1.ST7232AK2-AUTO.pdf
(201 pages)
Specifications of ST7232AK2-Auto
Hdflash Endurance
100 cycles, data retention
Clock Sources
crystal/ceramic resonator oscillators and bypass for external clock
Four Power Saving Modes
halt, active halt, wait and slow
Main Clock Controller With
real time base, beep and clock-out capabilities
Two 16-bit Timers With
2 input captures, 2 output compares, PWM and pulse generator modes
- Current page: 66 of 201
- Download datasheet (4Mb)
I/O ports
9.3
66/201
I/O port implementation
Analog alternate function
When the pin is used as an ADC input, the I/O must be configured as floating input. The
analog multiplexer (controlled by the ADC registers) switches the analog voltage present on
the selected pin to the common analog rail which is connected to the ADC input.
It is recommended not to change the voltage level or loading on any port pin while
conversion is in progress. Furthermore it is recommended not to have clocking pins located
close to a selected analog pin.
The hardware implementation on each I/O port depends on the settings in the DDR and OR
registers and specific feature of the I/O port such as ADC input or true open drain.
Switching these I/O ports from one state to another should be done in a sequence that
prevents unwanted side effects. Recommended safe transitions are illustrated in
Other transitions are potentially risky and should be avoided, since they are likely to present
unwanted side-effects such as spurious interrupt generation. The I/O port register
configurations are summarized in
Figure 27. Interrupt I/O port state transitions
Warning:
The analog input voltage level must be within the limits
stated in the absolute maximum ratings.
floating/pull-up
interrupt
Input
01
Table 20
(reset state)
floating
Input
00
XX
below.
= DDR, OR
open-drain
Output
10
push-pull
Output
11
ST7232Axx-Auto
Figure 27
Related parts for ST7232AK2-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-BIT MCU WITH 8K FLASH/ROM, ADC, 4 TIMERS, SPI, SCI INTERFACE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: