mt90528ag2 Zarlink Semiconductor, mt90528ag2 Datasheet - Page 47

• Manufacturer Part Number: mt90528ag2
• Description: 28-port Primary Rate Circuit Emulation Aal1 Sar
• Manufacturer: Zarlink Semiconductor

MT90528
Data Sheet
1- If the comparison is true (i.e., 2 MSB of the read pointer = turn), there is no underrun.
2- If the previous comparison is false, a second comparison (2 MSB of the read pointer = turn + 1 or 2 MSB of
the read pointer = turn + 2) is performed. If this comparison is true, a simple underrun has occurred. The
REPLAY_NSILENCE bit is checked: if it is set, the reassembly process keeps reading (old data) from the circular
buffer. If it is not set, a silence byte (as configured in Main TDM Control Register 1) is written to the port’s TDM
Output Buffer for the underrunning channel. If the SU bit is set in the TDM SDT Reassembly Control Structure, a
simple underrun is reported in the port’s TDM Control Register 4.
3- If the two previous comparisons are false, a third comparison (2 MSB of the read pointer = turn + 3) is
performed. If this comparison is true, a permanent underrun has occurred. The REPLAY_NSILENCE bit is checked:
if it is set, the reassembly process keeps reading (old data) from the circular buffer. If it is not set, a silence byte (as
configured in Main TDM Control Register 1) is written to the port’s TDM Output Buffer for the underrunning channel.
If the PU bit is set in the TDM SDT Reassembly Control Structure, a permanent underrun is reported in the port’s
TDM Control Registers 4, and 5 or 6.
Once a permanent underrun is detected on a TDM channel, underrun data (silence or old buffer data) will be sent
out on DSTo[p] until the channel’s permanent underrun bit is cleared in TDM5_Pp or TDM6_Pp.
Underrun Considerations
The SDT TDM reassembly process internal to the MT90528 performs underrun detection. Underruns are declared
when the receive circular buffer does not have valid data to play out onto the TDM bus. The underrun detection is
performed on a per channel basis for each of the up to 32 channels on a TDM port. The underrunning channels are
reported TDM Control Register 4, TDM Control Register 5 and TDM Control Register 6.
Each active channel in a VC may be used independently to perform underrun detection. For example, in a 10
channel VC, each of the 10 channels may have their underrun detection activated. Thus all 10 channels are
programmed to report underrun to the host processor. However the same functionality may be achieved by
reporting underrun on a single channel in the VC, thereby reducing the amount of work required of the host
processor and the number of interrupts generated. Given that all the channels are part of the same VC and will
experience the same cell loss and CDV, when one channel underruns, they all underrun. So, for the example given,
one channel would have its underrun detection activated and the 9 other channels would have their underrun
detection disabled.
Internal to the MT90528 the underrun detection mechanism is dependent on the active channel order of the output
TDM bus DSTo. Underrun is mis-reported on any channel (x) for which an upper channel (x+4) is not active on the
same TDM port. As an example, channel 5 underrun status would be mis-reported if channel 9 of the same output
TDM port was inactive. Given this operation it is suggested that underrun detection be enabled only on receive
channels in a VC that are not mis-reporting underrun. Those channels which are mis-reporting underrun would
have their underrun detection disabled. Note again that only a single channel per receive VC is required to have its
underrun detection enabled to provide the equivalent functionality as all receive channels in a VC detecting
underrun.
Silence Insertion
During an underrun condition bit 10 of TDM Control Register 3, REPLAY_N_SILENCE, is used to indicate whether
old data or a silence byte will be played out onto the TDM bus signal DSTo. This bit is programmable on a per port
basis. When the bit is set to 1 or REPLAY, old data from the reassembly circular buffer will be played out. When the
bit is set to 0 or SILENCE, a programmable silence byte is played out onto the DSTo channel. The silence byte to
be played out is programmed into the Main TDM Control Register 1, bits <15:8>.
When an active channel is mis-reporting an underrun condition the REPLAY_N_SILENCE bit still controls what
data is played out onto the TDM bus. If this bit is set to 1 for REPLAY the correct data will be played out. If the bit is
set to 0 for SILENCE then the silence byte will be played out rather than the correct data. As such, for bit error free
operation, the REPLAY option must be selected for any TDM port where an active channel is mis-reporting an
underrun condition.
47
Zarlink Semiconductor Inc.