HD6432621 Hitachi, HD6432621 Datasheet - Page 601
HD6432621
Manufacturer Part Number
HD6432621
Description
(HD64F262x Series) 16-Bit Microcomputer
Manufacturer
Hitachi
Datasheet
1.HD6432621.pdf
(1069 pages)
- Current page: 601 of 1069
- Download datasheet (5Mb)
15.3.2
After a hardware reset, the following initialization processing should be carried out:
These initial settings must be made while the HCAN is in bit configuration mode. Configuration
mode is a state in which the reset request bit (MCR0) in the master control register (MCR) is 1 and
the reset status bit in the general status register (GSR) is also 1 (GSR3 = 1). Configuration mode is
exited by clearing the reset request bit in MCR to 0; when MCR0 is cleared to 0, the HCAN
automatically clears the reset state bit (GSR3) in the general status register (GSR). The power-up
sequence then begins, and communication with the CAN bus is possible as soon as the sequence
ends. The power-up sequence consists of the detection of 11 consecutive recessive bits.
IRR0 Clearing: The reset interrupt flag (IRR0) is always set after a reset or recovery from
software standby mode. As an HCAN interrupt is initiated immediately when interrupts are
enabled, IRR0 should be cleared.
Bit Rate and Bit Timing Settings: As bit rate settings, a baud rate setting and bit timing setting
must be made each time a CAN node begins communication. The baud rate and bit timing settings
are made in the bit configuration register (BCR).
a. Note
Clearing of IRR0 bit in interrupt register (IRR)
Bit rate setting
Mailbox transmit/receive settings
Mailbox (RAM) initialization
Message transmission method setting
BCR can be written to at all times, but should only be modified in configuration mode.
Settings should be made so that all CAN controllers connected to the CAN bus have the same
baud rate and bit width.
Refer to table 15-3 for the range of values that can be used as settings (TSEG1, TSEG2, BRP,
sample point, and SJW) for BCR.
Initialization after Hardware Reset
557
Related parts for HD6432621
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Silicon N-Channel Power MOS FET Module
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
High Speed Power Switching
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
Silicon N-Channel IGBT
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
8MHz V(cc): -0.3 to +7.0V V(in): -0.3 to +0.3V advanced CRT controller (ACRTC)
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-WORD x 4-BIT MULTIPORT CMOS VIDEO RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
65,536-word ? 4-bit High Speed CMOS Static RAM
Manufacturer:
HITACHI
Datasheet:
Part Number:
Description:
SINGLE CHIP CODEC WITH FILTERS(COMBO)
Manufacturer:
HITACHI
Datasheet: