122-28176 Parallax Inc, 122-28176 Datasheet - Page 237
122-28176
Manufacturer Part Number
122-28176
Description
GUIDE STUDENT PROCESS CONTROL
Manufacturer
Parallax Inc
Specifications of 122-28176
Accessory Type
Manual
Product
Microcontroller Accessories
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
For Use With/related Products
Propeller Education (PE) Kit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
- Current page: 237 of 330
- Download datasheet (11Mb)
CalcTemp:
Drive_Heater:
PlotTemp:
When you start your system, the heater will be on as indicated by the LED. The
heater/resistor becomes quite hot when full power is applied. This heat transfers through
the environment and warms the temperature sensor. When the sensor has heated to 101.5,
the BASIC Stamp will turn off the heater. For a period after the heater is turned off, the
temperature continues to rise. This is called overshoot. At this point, it is important to
understand the dynamics of your system. The heat held within the mass of the resistor
will continue to dissipate into the air, the air becomes warmer, and the LM34 reports that
overshoot has occurred. Similar to the mechanical inertia of a moving object, this
phenomenon is called thermal inertia.
Overshoot becomes large when the heat energy contained in the mass of the resistor is
large, relative to the heat already in the test tube. The test tube is small, but the mass of
HIGH ADC_CS
RETURN
TempF = (V_Span * 100)/255 * ADC_ByteValue + (V_Offset * 100)
RETURN
IF TempF > SetPoint THEN
ELSE
ENDIF
RETURN
DEBUG "[", DEC TempF,",/,100]", ",",
DEBUG "!O txtTemp=(AINVAL0)",CR
DEBUG IBIN Heater, BIN Fan,CR
RETURN
√
√
√
√
√
√
LOW Heater
HIGH Heater
Open StampPlot macro sic_pc_incubator_on_off.spm
Verify the Lower and Upper Temperatures for monitoring are 70 to 120
respectively.
Verify the setpoint is 101.5.
Connect and Plot
Note the action of the incubator as it rises to the setpoint.
Once temperature has stabilized, clear the min/max temperatures and monitor for
several minutes.
"[", DEC SetPoint, ",/,100]",CR
' Disable ADC
' Transfer function for temperature in hundreths
' Determine heater state
' Above setpoint - Heat off
' Below setpoint - Heat on
' Plot temperature
' and setpoint
' Update temperature reading
' Plot fan as digital
Related parts for 122-28176
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MANUAL FOR SUMOBOT
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
GUIDE STUDENT SMART SENSORS
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
MANUAL PROPELLER
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
LEAD WIRES FLYING CABLE III/IV
Manufacturer:
Xilinx Inc
Datasheet:
Part Number:
Description:
BOARD ADAPTER AND FLY LEADS
Manufacturer:
Xilinx Inc
Datasheet:
Part Number:
Description:
PLATFORM CABLE USB II
Manufacturer:
Xilinx Inc
Datasheet:
Part Number:
Description:
KIT STARTER COOLRUNNER-II BUNDLE
Manufacturer:
Xilinx Inc
Datasheet:
Part Number:
Description:
Microcontroller Modules & Accessories DISCONTINUED BY PARALLAX
Manufacturer:
Parallax Inc
Part Number:
Description:
Microcontroller Modules & Accessories DISCONTINUED BY PARALLAX
Manufacturer:
Parallax Inc
Part Number:
Description:
BOOK UNDERSTANDING SIGNALS
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
BOARD EXPERIMENT+LCD NX-1000
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
IC MCU 2K FLASH 50MHZ SO-18
Manufacturer:
Parallax Inc
Datasheet: