MCF5407AI220 Freescale Semiconductor, MCF5407AI220 Datasheet - Page 179

• Manufacturer Part Number: MCF5407AI220
• Description: IC MPU 32B 220MHZ COLDF 208-FQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF540xr

Specifications of MCF5407AI220

• Core Processor: Coldfire V4
• Core Size: 32-Bit
• Speed: 220MHz
• Connectivity: EBI/EMI, I²C, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 208-FQFP
• Maximum Clock Frequency: 220 MHz
• Operating Supply Voltage: 1.8 V, 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Program Memory Size: 24KB
• Cpu Speed: 220MHz
• Embedded Interface Type: I2C, UART
• Digital Ic Case Style: FQFP
• No. Of Pins: 208
• Supply Voltage Range: 3.3V
• Rohs Compliant: Yes
• For Use With: M5407C3 - KIT EVAL FOR MCF5407 W/ETHERNET
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The assertion of BKPT should be considered in the following two special cases:
CSR[27–24] indicates the halt source, showing the highest priority source for multiple halt
conditions. Debug module Revisions A and B clear CSR[27–24] upon a read of the CSR,
but Revision C (in the MCF5407) does not. The debug
HALT can be recognized by counting 0xFF occurrences on PSTDDATA. The count is
necessary to determine between a possible data output value of 0xFF and the HALT
condition. Because data always follows a marker (0x8, 0x9, 0xA, or 0xB), PSTDDATA can
display no more than four data 0xFFs. Two such scenarios exist:
4. The assertion of the BKPT input is treated as a pseudo-interrupt; that is, the halt
• After the system reset signal is negated, the processor waits for 16 clock cycles
• The ColdFire architecture also handles a special case of BKPT being asserted while
• A B marker occurs on the left nibble of PSTDDATA with the data of 0xFF
condition is postponed until the processor core samples for halts/interrupts. The
processor samples for these conditions once during the execution of each
instruction. If there is a pending halt condition at the sample time, the processor
suspends execution and enters the halted state.
before beginning reset exception processing. If the BKPT input is asserted within
eight cycles after RSTI is negated, the processor enters the halt state, signaling halt
status (0xF) on the PSTDDATA outputs. While the processor is in this state, all
resources accessible through the debug module can be referenced. This is the only
chance to force the processor into emulation mode through CSR[EMU].
After system initialization, the processor’s response to the
the set of BDM commands performed while it is halted for a breakpoint.
Specifically, if the PC register was loaded, the
exit halted state and pass control to the instruction address in the PC, bypassing
normal reset exception processing. If the PC was not loaded, the
causes the processor to exit halted state and continue reset exception processing.
the processor is stopped by execution of the STOP instruction. For this case, the
processor exits the stopped mode and enters the halted state, at which point, all BDM
commands may be exercised. When restarted, the processor continues by executing
the next sequential instruction, that is, the instruction following the STOP opcode.
following:
PSTDDATA[7:0]
0xBF
0xFF
0xFF
0xFF
0xFX (X indicates that the next PST value is guaranteed to not be 0xF)
Chapter 5. Debug Support
GO
GO
command causes the processor to
command clears CSR[26–24].
Background Debug Mode (BDM)
GO
command depends on
GO
command
5-23