ADSP-21161NKCAZ100 Analog Devices Inc, ADSP-21161NKCAZ100 Datasheet - Page 12

• Manufacturer Part Number: ADSP-21161NKCAZ100
• Description: IC,DSP,32-BIT,CMOS,BGA,225PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Fixed/Floating Pointr

Specifications of ADSP-21161NKCAZ100

• Rohs Compliant: YES
• Interface: Host Interface, Link Port, Serial Port
• Clock Rate: 100MHz
• Non-volatile Memory: External
• On-chip Ram: 128kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.80V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 225-MBGA, 225-Mini-BGA
• Device Core Size: 32b
• Architecture: Enhanced Harvard
• Format: Floating Point
• Clock Freq (max): 100MHz
• Mips: 100
• Device Input Clock Speed: 100MHz
• Ram Size: 128KB
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (min): 1.71/3.13V
• Operating Supply Voltage (max): 1.89/3.47V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 225
• Package Type: CSPBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADSP21161NKCAZ100

ADSP-21161N
PIN FUNCTION DESCRIPTIONS
ADSP-21161N pin definitions are listed below. Inputs identified
as synchronous (S) must meet timing requirements with respect
to CLKIN (or with respect to TCK for TMS, TDI). Inputs iden-
tified as asynchronous (A) can be asserted asynchronously to
CLKIN (or to TCK for TRST).Tie or pull unused inputs to
V
Table 2. Pin Function Descriptions
Pin
ADDR23–0
DATA47–16
MS3–0
RD
WR
DDEXT
• ADDR23–0, DATA47–0, BRST, CLKOUT (Note: These
• PA, ACK, RD, WR, DMARx, DMAGx, (ID2–0 = 00x)
• LxCLK, LxACK, LxDAT7–0 (LxPDRDE = 0) (Note: See
• DxA, DxB, SCLKx, SPICLK, MISO, MOSI, EMU,
pins have a logic-level hold circuit enabled on the
ADSP-21161N DSP with ID2–0 = 00x.)
(Note: These pins have a pull-up enabled on the
ADSP-21161N DSP with ID2–0 = 00x.)
Link Port Buffer Control Register Bit definitions in the
ADSP-21161N SHARC DSP Hardware Reference.)
TMS,TRST, TDI (Note: These pins have a pull-up.)
or GND, except for the following:
Type
I/O/T
I/O/T
I/O/T
I/O/T
I/O/T
Function
External Bus Address. The ADSP-21161N outputs addresses for external memory and peripherals on these
pins. In a multiprocessor system the bus master outputs addresses for read/writes of the IOP registers of other
ADSP-21161Ns while all other internal memory resources can be accessed indirectly via DMA control (that
is, accessing IOP DMA parameter registers). The ADSP-21161N inputs addresses when a host processor or
multiprocessing bus master is reading or writing its IOP registers. A keeper latch on the DSP’s ADDR23-0 pins
maintains the input at the level it was last driven. This latch is only enabled on the ADSP-21161N with
ID2–0=00x.
External Bus Data. The ADSP-21161N inputs and outputs data and instructions on these pins. Pull-up
resistors on unused data pins are not necessary. A keeper latch on the DSP’s DATA47–16 pins maintains the
input at the level it was last driven. This latch is only enabled on the ADSP-21161N with ID2–0=00x.
Note: DATA15–8 pins (multiplexed with L1DAT7–0) can also be used to extend the data bus if the link ports are
disabled and will not be used. In addition, DATA7–0 pins (multiplexed with L0DAT7–0) can also be used to extend
the data bus if the link ports are not used. This enables execution of 48-bit instructions from external SBSRAM
(system clock speed-external port), SRAM (system clock speed-external port) and SDRAM (core clock or one-half
the core clock speed). The IPACKx Instruction Packing Mode Bits in SYSCON should be set correctly (IPACK1–0=0x1)
to enable this full instruction Width/No-packing Mode of operation.
Memory Select Lines. These outputs are asserted (low) as chip selects for the corresponding banks of
external memory. Memory bank sizes are fixed to 16 M words for non-SDRAM and 64M words for SDRAM.
The MS3–0 outputs are decoded memory address lines. In asynchronous access mode, the MS3–0 outputs
transition with the other address outputs. In synchronous access modes, the MS3–0 outputs assert with the
other address lines; however, they deassert after the first CLKIN cycle in which ACK is sampled asserted. In a
multiprocessor system, the MSx signals are tracked by slave SHARCs.
Memory Read Strobe. RD is asserted whenever ADSP-21161N reads a word from external memory or from
the IOP registers of other ADSP-21161Ns. External devices, including other ADSP-21161Ns, must assert RD
for reading from a word of the ADSP-21161N IOP register memory. In a multiprocessing system, RD is driven
by the bus master. RD has a 20 k internal pull-up resistor that is enabled for DSPs with ID2–0=00x.
Memory Write Low Strobe. WR is asserted when ADSP-21161N writes a word to external memory or IOP
registers of other ADSP-21161Ns. External devices must assert WR for writing to ADSP-21161N IOP registers.
In a multiprocessing system, the bus master drives WR. WR has a 20 k internal pull-up resistor that is enabled
for DSPs with ID2–0=00x.
Rev. B | Page 12 of 60 | November 2009
The following symbols appear in the Type column of
A = Asynchronous, G = Ground, I = Input, O = Output,
P = Power Supply, S = Synchronous, (A/D) = Active Drive,
(O/D) = Open Drain, and T = Three-State (when SBTS is
asserted or when the ADSP-21161N is a bus slave).
Unlike previous SHARC processors, the ADSP-21161N con-
tains internal series resistance equivalent to 50
input/output drivers except the CLKIN and XTAL pins.
Therefore, for traces longer than six inches, external series resis-
tors on control, data, clock, or frame sync pins are not required
to dampen reflections from transmission line effects for point-
to-point connections. However, for more complex networks
such as a star configuration, series termination is still
recommended.
on all
Table
2: