DSPIC33FJ128MC706-I/PT Microchip Technology Inc., DSPIC33FJ128MC706-I/PT Datasheet - Page 219

• Manufacturer Part Number: DSPIC33FJ128MC706-I/PT
• Description: 16 BIT MCU/DSP 64LD 40MIPS 128KB FLASH
• Manufacturer: Microchip Technology Inc.
• Type: DSPr

Specifications of DSPIC33FJ128MC706-I/PT

• A/d Inputs: 16-Channels, 12-Bit
• Comparators: 8
• Cpu Speed: 40 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 53
• Interface: CAN/I2C/SPI/UART
• Ios: 53
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 64-pin TQFP
• Programmable Memory: 128K Bytes
• Ram Size: 16K Bytes
• Timers: 9-16-bit, 4-32-bit
• Voltage, Range: 3-3.6
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

REGISTER 18-1:
© 2006 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
I2CEN
R/W-0
R/W-0
GCEN
I2CEN: I2Cx Enable bit
1 = Enables the I2Cx module and configures the SDAx and SCLx pins as serial port pins
0 = Disables the I2Cx module. All I
Unimplemented: Read as ‘0’
I2CSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters an Idle mode
0 = Continue module operation in Idle mode
SCLREL: SCLx Release Control bit (when operating as I
1 = Release SCLx clock
0 = Hold SCLx clock low (clock stretch)
If STREN = 1:
Bit is R/W (i.e., software may write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware clear
at beginning of slave transmission. Hardware clear at end of slave reception.
If STREN = 0:
Bit is R/S (i.e., software may only write ‘1’ to release clock). Hardware clear at beginning of slave
transmission.
IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit
1 = IPMI mode is enabled; all addresses Acknowledged
0 = IPMI mode disabled
A10M: 10-bit Slave Address bit
1 = I2CxADD is a 10-bit slave address
0 = I2CxADD is a 7-bit slave address
DISSLW: Disable Slew Rate Control bit
1 = Slew rate control disabled
0 = Slew rate control enabled
SMEN: SMBus Input Levels bit
1 = Enable I/O pin thresholds compliant with SMBus specification
0 = Disable SMBus input thresholds
GCEN: General Call Enable bit (when operating as I
1 = Enable interrupt when a general call address is received in the I2CxRSR
0 = General call address disabled
STREN: SCLx Clock Stretch Enable bit (when operating as I
Used in conjunction with SCLREL bit.
1 = Enable software or receive clock stretching
0 = Disable software or receive clock stretching
STREN
R/W-0
(module is enabled for reception)
U-0
—
I2CxCON: I2Cx CONTROL REGISTER
U = Unimplemented bit, read as ‘0’
W = Writable bit
‘1’ = Bit is set
I2CSIDL
ACKDT
R/W-0
R/W-0
R/W-1 HC
R/W-0 HC
SCLREL
ACKEN
Preliminary
2
C pins are controlled by port functions.
HS = Set in hardware
‘0’ = Bit is cleared
R/W-0 HC
IPMIEN
R/W-0
RCEN
2
C slave)
2
C slave)
R/W-0 HC
2
R/W-0
A10M
C slave)
PEN
HC = Cleared in hardware
x = Bit is unknown
R/W-0 HC
DISSLW
dsPIC33F
R/W-0
RSEN
DS70165D-page 217
R/W-0 HC
R/W-0
SMEN
SEN
bit 8
bit 0