DS26324GNA3+ Maxim Integrated Products, DS26324GNA3+ Datasheet - Page 71

• Manufacturer Part Number: DS26324GNA3+
• Description: IC LIU E1/T1/J1 3.3V 256-CSBGA
• Manufacturer: Maxim Integrated Products
• Type: Line Interface Units (LIUs)r

Specifications of DS26324GNA3+

• Number Of Drivers/receivers: 16/16
• Protocol: LIN
• Voltage - Supply: 3.135 V ~ 3.465 V
• Mounting Type: Surface Mount
• Package / Case: 256-CSBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Register Name:
Register Description:
Register Address (LIUs 1–8):
Bit #
Name
Default
Bit 7: Receiver Transformer Turns Ratio Channel 4 (RTR4). If this bit is set the turns ratio is 1:1 on the receiver
side. This bit should be set when a 1:1 receiver transformer is used. Note that in order to use fully internal receive
impedance termination, a 1:1 transformer must be used and this bit must be set to 1.
Bit 6 to 4: Channel 4 Receive Sensitivity/Monitor Select [2:0] (C4RSM[2:0]). Bits C4RSM[2:0] are used to
select the receiver sensitivity level and the monitor mode resistive gain. See
Bit 3: Receiver Transformer Turns Ratio Channel 3 (RTR3). If this bit is set the turns ratio is 1:1 on the receiver
side. This bit should be set when a 1:1 receiver transformer is used. Note that in order to use the fully internal
receive impedance termination, a 1:1 transformer must be used and this bit must be set to 1.
Bit 2 to 0: Channel 3 Receive Sensitivity/Monitor Select [2:0] (C3RSM[2:0]). Bits C3RSM[2:0] are used to
select the receiver sensitivity level and the monitor mode resistive gain. See
Register Address (LIUs 9–16):
Bit #
Name
Default
Bit 7: Receiver Transformer Turns Ratio Channel 12 (RTR12). If this bit is set the turns ratio is 1:1 on the
receiver side. This bit should be set when a 1:1 receiver transformer is used. Note that in order to use fully internal
receive impedance termination, a 1:1 transformer must be used and this bit must be set to 1.
Bits 6 to 4: Channel 12 Receive Sensitivity/Monitor Select [2:0] (C12RSM[2:0]). Bits C12RSM[2:0] are used to
select the receiver sensitivity level and the monitor mode resistive gain. See
Bit 3: Receiver Transformer Turns Ratio Channel 11 (RTR11). If this bit is set the rurns ratio is 1:1 on the
receiver side. This bit should be set when a 1:1 receiver transformer is used. Note that in order to use the fully
internal receive impedance termination, a 1:1 transformer must be used and this bit must be set to 1.
Bits 2 to 0: Channel 11 Receive Sensitivity/Monitor Select [2:0] (C11RSM[2:0]). Bits C11RSM[2:0] are used to
select the receiver sensitivity level and the monitor mode resistive gain. See
RTR12
RTR4
7
0
7
0
C12RSM2
C4RSM2
6
0
6
0
RSMM2
Receive Sensitivity Monitor Mode 2
09h
29h
C12RSM1
C4RSM1
5
0
5
0
DS26324 3.3V, 16-Channel, E1/T1/J1 Short-Haul Line Interface Unit
C12RSM0
C4RSM0
71 of 120
4
0
4
0
RTR11
RTR3
3
0
3
0
Table
Table
Table
Table
C11RSM2
C3RSM2
2
0
2
0
6-16.
6-16.
6-16.
6-16.
C11RSM1
C3RSM1
1
0
1
0
C11RSM0
C3RSM0
0
0
0
0