ATmega16HVB Atmel Corporation, ATmega16HVB Datasheet - Page 130

• Manufacturer Part Number: ATmega16HVB
• Manufacturer: Atmel Corporation

Specifications of ATmega16HVB

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 8 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 17
• Ext Interrupts: 15
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1.9
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 4.0 to 25
• Operating Voltage (vcc): 4.0 to 25
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

23.3
23.4
23.5
130
Regulator start-up
Battery pack short detection
Black-out detection
ATmega16HVB/32HVB
When the chip is in power-off mode the Voltage Regulator will be off and there will be no con-
nection between VFET and VREG.
The regulator is started when the Charger Detect module detects that a charger is connected
(for details on Charger Detect, see
the Voltage Regulator will stay in a force mode where the VREG output is raised against the
VFET input voltage. As VREG increases to the target voltage level the regulator will automati-
cally enter regulation mode, with a stable output voltage of nominally 3.3V.
44, in System Control and Reset illustrates the start-up sequence from power-off.
The Voltage Regulator will continuously monitor the operating condition at the VFET terminal. If
the voltage at VFET drops below the Regulator Short-circuit Level (RSCL), see
acteristics” on page
mode, VFET is disconnected from VREG to avoid a quick drop in the voltage regulator output.
When the voltage regulator enters this mode, the chip will be completely powered by the exter-
nal reservoir capacitor (CREG). This allows the chip to operate a certain time without entering
BOD reset, even if the VFET voltage is too low for the voltage regulator to operate.
An interrupt is issued when the regulator enters Battery Pack Short mode, if the ROCWIE bit in
ROCR Register is set. This allows actions to be taken to reduce power consumption and hence
prolonging the time that CREG can be used to power the chip.
In a typical short-circuit situation, VFET will drop as a consequence of high current consumption,
and recover as soon as the Battery Protection module has disabled the FETs. Hence CREG
should be dimensioned so that the chip can sustain operation without entering BOD reset, until
the FETs are disabled either by HW or SW.
To minimize power consumption when the Voltage Regulator enters the Battery Pack Short
mode, the chip should enter Power-save sleep mode as soon as possible after the ROCWIF
interrupt is detected. The Watchdog Timer should be configured to wake up the CPU after a time
that is considered safe, see
Software should then check the status of the ROC flag. If the ROCS flag is cleared, normal oper-
ation may be resumed.
To ensure that the internal logic has safe operating condition, the Voltage Regulator has built-in
Black-Out Detector (BLOD). If the voltage at the VREG pin drops below the Black-out Detection
Level, V
BLOT
, the chip will automatically enter Power-off mode.
225, the Voltage Regulator enters the Battery Pack Short mode. In this
application note AVR132
”Charger detect” on page
for use of enhanced Watchdog Timer.
126). When starting the regulator
Figure 11-2 on page
”Electrical char-
8042D–AVR–10/11