ATmega16HVB Atmel Corporation, ATmega16HVB Datasheet - Page 204

• Manufacturer Part Number: ATmega16HVB
• Manufacturer: Atmel Corporation

Specifications of ATmega16HVB

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 8 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 17
• Ext Interrupts: 15
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1.9
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 4.0 to 25
• Operating Voltage (vcc): 4.0 to 25
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

30. Memory programming
30.1
204
Program and data memory lock bits
ATmega16HVB/32HVB
The Atmel ATmega16HVB/32HVB provides six Lock bits which can be left unprogrammed (“1”)
or can be programmed (“0”) to obtain the additional features listed in
can only be erased to “1” with the Chip Erase command
Table 30-1.
Note:
Table 30-2.
Lock bit byte
BLB12
BLB11
BLB02
BLB01
LB2
LB1
Mode
BLB0
Mode
LB
1
2
3
1
2
3
4
Memory lock bits
1. “1” means unprogrammed, “0” means programmed.
BLB02
LB2
Lock bit byte
Lock bit protection modes
1
1
0
1
1
0
0
BLB01
LB1
1
0
0
1
0
0
1
(1)
.
Bit No
Protection type
No memory lock features enabled
Further programming of the Flash and EEPROM is disabled in
Parallel and Serial Programming mode. The Fuse bits are locked in
both Serial and Parallel Programming mode
Further programming and verification of the Flash and EEPROM is
disabled in Parallel and Serial Programming mode. The Boot Lock
bits and Fuse bits are locked in both Serial and Parallel
Programming mode
No restrictions for SPM or LPM accessing the Application section
SPM is not allowed to write to the Application section
SPM is not allowed to write to the Application section, and LPM
executing from the Boot Loader section is not allowed to read from
the Application section. If Interrupt Vectors are placed in the Boot
Loader section, interrupts are disabled while executing from the
Application section
LPM executing from the Boot Loader section is not allowed to read
from the Application section. If Interrupt Vectors are placed in the
Boot Loader section, interrupts are disabled while executing from
the Application section
7
6
5
4
3
2
1
0
(1)(2)
.
Description
–
–
Boot lock bit
Boot lock bit
Boot lock bit
Boot lock bit
Lock bit
Lock bit
(1)
Table
Default value
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
(1)
30-2. The Lock bits
8042D–AVR–10/11