ATmega16HVB Atmel Corporation, ATmega16HVB Datasheet - Page 225

• Manufacturer Part Number: ATmega16HVB
• Manufacturer: Atmel Corporation

Specifications of ATmega16HVB

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 8 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 17
• Ext Interrupts: 15
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1.9
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 4.0 to 25
• Operating Voltage (vcc): 4.0 to 25
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

32. Electrical characteristics
32.1
32.2
Table 32-1.
8042D–AVR–10/11
Operating temperature..................................... -40°C to +85°C
Storage temperature...................................... -65°C to +150°C
Voltage on PA0 - PA3, PI, NI, PPI and NNI
with respect to ground .............................. -0.5V to V
Voltage on PB0 - PB7
with respect to ground .............................. -0.5V to VCC +0.5V
Voltage on PC0 - PC4,
PV1, and NV with respect to ground..................-0.5V to +6.0V
Voltage on OC and OD with respect to ground...-0.5V to +35V
Voltage on PC5, BATT, PVT, VFET, PV4, PV3, and PV2
with respect to ground ........................................-0.5V to +25V
Voltage on PV4 with respect to PV3: ................. -0.5V to +10V
Voltage on PV3 with respect to PV2: ................. -0.5V to +10V
Voltage on PV2 with respect to PV1: ................. -0.5V to +10V
Voltage on PV1 with respect to NV: ................... -0.5V to +10V
Voltage on PVT with respect to VFET: .............................. 10V
Voltage on VCLMP10 and RESET
with respect to ground ........................................-0.5V to +13V
Maximum operating voltage on VREG and VCC .............. 4.5V
Maximum operating voltage on VFET ............................... 18V
Symbol
I
VFET
Absolute maximum ratings*
Supply current characteristics
Parameter
Active current
Idle current
ADCNRM current
Power-save
current
Power-off current
T
A
= 25°C unless otherwise noted.
Condition
VFET = 16V, CPU clock = 8MHz, All PRR bits set
VFET = 16V, CPU clock = 1MHz, All PRR bits set
VFET = 16V, CPU clock = 1MHz, All PRR bits set
VFET = 16V, CPU clock = 1MHz, All PRR bits except
PRVADC are set, VADC enabled
VFET = 16V, Only WDT enabled, DUVR mode disabled
VFET = 16V, WDT, CC-ADC, OC, OD and Battery
Protection enabled, DUVR mode disabled
VFET = 6V
REG
+0.5V
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
ATmega16HVB/32HVB
Minimum
Typical
3.75
760
215
350
115
28
<1
Maximum
1000
293
170
46
5
2
Units
mA
µA
225