ATmega324PA Atmel Corporation, ATmega324PA Datasheet - Page 220

• Manufacturer Part Number: ATmega324PA
• Manufacturer: Atmel Corporation

Specifications of ATmega324PA

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8272C–AVR–06/11
1
2
3
4
5
6
7
Assembly Code Example
ldi
out
wait1:
in
sbrs r16,TWINT
rjmp wait1
in
andi r16, 0xF8
cpi
brne ERROR
ldi
out
ldi
out
wait2:
in
sbrs r16,TWINT
rjmp wait2
in
andi r16, 0xF8
cpi
brne ERROR
ldi
out
ldi
out
wait3:
in
sbrs r16,TWINT
rjmp wait3
in
andi r16, 0xF8
cpi
brne ERROR
ldi
out
r16, (1<<TWINT)|(1<<TWSTA)|
(1<<TWEN)
TWCR, r16
r16,TWCR
r16,TWSR
r16, START
r16, SLA_W
TWDR, r16
r16, (1<<TWINT) | (1<<TWEN)
TWCR, r16
r16,TWCR
r16,TWSR
r16, MT_SLA_ACK
r16, DATA
TWDR, r16
r16, (1<<TWINT) | (1<<TWEN)
TWCR, r16
r16,TWCR
r16,TWSR
r16, MT_DATA_ACK
r16, (1<<TWINT)|(1<<TWEN)|
(1<<TWSTO)
TWCR, r16
• After all TWI Register updates and other pending application software tasks have been
In the following an assembly and C implementation of the example is given. Note that the code
below assumes that several definitions have been made, for example by using include-files.
completed, TWCR is written. When writing TWCR, the TWINT bit should be set. Writing a one
to TWINT clears the flag. The TWI will then commence executing whatever operation was
specified by the TWCR setting.
ATmega164A/PA/324A/PA/644A/PA/1284/P
C Example
TWCR = (1<<TWINT)|(1<<TWSTA)|
while (!(TWCR & (1<<TWINT)))
if ((TWSR & 0xF8) != START)
TWDR = SLA_W;
TWCR = (1<<TWINT) | (1<<TWEN); Load SLA_W into TWDR Register.
while (!(TWCR & (1<<TWINT)))
if ((TWSR & 0xF8) !=
MT_SLA_ACK)
TWDR = DATA;
TWCR = (1<<TWINT) | (1<<TWEN); Load DATA into TWDR Register.
while (!(TWCR & (1<<TWINT)))
if ((TWSR & 0xF8) !=
MT_DATA_ACK)
TWCR = (1<<TWINT)|(1<<TWEN)|
(1<<TWEN)
(1<<TWSTO);
;
ERROR();
;
ERROR();
;
ERROR();
Comments
Send START condition
Wait for TWINT Flag set. This
indicates that the START condition
has been transmitted
Check value of TWI Status
Register. Mask prescaler bits. If
status different from START go to
ERROR
Clear TWINT bit in TWCR to start
transmission of address
Wait for TWINT Flag set. This
indicates that the SLA+W has been
transmitted, and ACK/NACK has
been received.
Check value of TWI Status
Register. Mask prescaler bits. If
status different from MT_SLA_ACK
go to ERROR
Clear TWINT bit in TWCR to start
transmission of data
Wait for TWINT Flag set. This
indicates that the DATA has been
transmitted, and ACK/NACK has
been received.
Check value of TWI Status
Register. Mask prescaler bits. If
status different from
MT_DATA_ACK go to ERROR
Transmit STOP condition
220