ATmega324PA Atmel Corporation, ATmega324PA Datasheet - Page 312

• Manufacturer Part Number: ATmega324PA
• Manufacturer: Atmel Corporation

Specifications of ATmega324PA

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.8
27.8.1
8272C–AVR–06/11
Serial Downloading
Serial Programming Pin Mapping
Both the Flash and EEPROM memory arrays can be programmed using a serial programming
bus while RESET is pulled to GND. The serial programming interface consists of pins SCK,
MOSI (input) and MISO (output). After RESET is set low, the Programming Enable instruction
needs to be executed first before program/erase operations can be executed. NOTE, in
27-15 on page
SPI pins dedicated for the internal Serial Peripheral Interface - SPI.
Table 27-15. Pin Mapping Serial Programming
Figure 27-10. Serial Programming and Verify
Notes:
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low: > 2 CPU clock cycles for f
High: > 2 CPU clock cycles for f
Symbol
MOSI
MISO
1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the
2. V
SCK
XTAL1 pin.
CC
ATmega164A/PA/324A/PA/644A/PA/1284/P
- 0.3V < AVCC < V
312, the pin mapping for serial programming is listed. Not all packages use the
(PDIP-40)
Pins
PB5
PB6
PB7
MOSI
MISO
SCK
ck
ck
CC
< 12MHz, 3 CPU clock cycles for f
< 12MHz, 3 CPU clock cycles for f
+ 0.3V, however, AVCC should always be within 1.8 - 5.5V
(TQFP/MLF-44)
XTAL1
RESET
GND
(1)
Pins
PB5
PB6
PB7
AVCC
VCC
+1.8 - 5.5V
+1.8 - 5.5V
I/O
O
I
I
(2)
ck
ck
≥ 12MHz
≥ 12MHz
Serial Data out
Serial Data in
Description
Serial Clock
Table
312