ATmega324PA Atmel Corporation, ATmega324PA Datasheet - Page 278

• Manufacturer Part Number: ATmega324PA
• Manufacturer: Atmel Corporation

Specifications of ATmega324PA

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.8
25.8.1
25.8.2
8272C–AVR–06/11
Register Description
MCUCR – MCU Control Register
MCUSR – MCU Status Register
The MCU Control Register contains control bits for general MCU functions.
Note:
• Bits 7 – JTD: JTAG Interface Disable
When this bit is zero, the JTAG interface is enabled if the JTAGEN Fuse is programmed. If this
bit is one, the JTAG interface is disabled. In order to avoid unintentional disabling or enabling of
the JTAG interface, a timed sequence must be followed when changing this bit: The application
software must write this bit to the desired value twice within four cycles to change its value. Note
that this bit must not be altered when using the On-chip Debug system.
The MCU Status Register provides information on which reset source caused an MCU reset.
• Bit 4 – JTRF: JTAG Reset Flag
This bit is set if a reset is being caused by a logic one in the JTAG Reset Register selected by
the JTAG instruction AVR_RESET. This bit is reset by a Power-on Reset, or by writing a logic
zero to the flag.
Bit
0x35 (0x55)
Read/Write
Initial Value
Bit
0x34 (0x54)
Read/Write
Initial Value
1. Only available in the ATmega164PA/324PA/644PA/1284P.
ATmega164A/PA/324A/PA/644A/PA/1284/P
JTD
R/W
7
0
R
7
–
0
BODS
R/W
6
0
R
6
–
0
(1)
BODSE
R/W
5
0
R
5
–
0
(1)
PUD
JTRF
R/W
R/W
4
0
4
WDRF
R/W
R
3
–
0
3
See Bit Description
BORF
R/W
R
2
–
0
2
IVSEL
EXTRF
R/W
R/W
1
0
1
IVCE
PORF
R/W
R/W
0
0
0
MCUCR
MCUSR
278