ATmega324PA Atmel Corporation, ATmega324PA Datasheet - Page 70

• Manufacturer Part Number: ATmega324PA
• Manufacturer: Atmel Corporation

Specifications of ATmega324PA

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

13.2.6
13.2.7
13.2.8
8272C–AVR–06/11
PCMSK3 – Pin Change Mask Register 3
PCMSK2 – Pin Change Mask Register 2
PCMSK1 – Pin Change Mask Register 1
• Bit 1 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT15:8 pin triggers an interrupt request, PCIF1 becomes set
(one). If the I-bit in SREG and the PCIE1 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 0 – PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7:0 pin triggers an interrupt request, PCIF0 becomes set
(one). If the I-bit in SREG and the PCIE0 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 7:0 – PCINT31:24: Pin Change Enable Mask 31:24
Each PCINT31:24-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT31:24 is set and the PCIE3 bit in PCICR is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT31:24 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
• Bit 7:0 – PCINT23:16: Pin Change Enable Mask 23..16
Each PCINT23:16-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT23:16 is set and the PCIE2 bit in PCICR is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT23:16 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
• Bit 7:0 – PCINT15:8: Pin Change Enable Mask 15..8
Each PCINT15:8-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT15:8 is set and the PCIE1 bit in EIMSK is set, pin change interrupt is enabled on the
corresponding I/O pin. If PCINT15:8 is cleared, pin change interrupt on the corresponding I/O
pin is disabled.
Bit
(0x73)
Read/Write
Initial Value
Bit
(0x6D)
Read/Write
Initial Value
Bit
(0x6C)
Read/Write
Initial Value
PCINT31
PCINT23
PCINT15
ATmega164A/PA/324A/PA/644A/PA/1284/P
R/W
R/W
R/W
7
0
7
0
7
0
PCINT30
PCINT22
PCINT14
R/W
R/W
R/W
6
0
6
0
6
0
PCINT29
PCINT21
PCINT13
R/W
R/W
R/W
5
0
5
0
5
0
PCINT28
PCINT20
PCINT12
R/W
R/W
R/W
4
0
4
0
4
0
PCINT27
PCINT19
PCINT11
R/W
R/W
R/W
3
0
3
0
3
0
PCINT26
PCINT18
PCINT10
R/W
R/W
R/W
2
0
2
0
2
0
PCINT25
PCINT17
PCINT9
R/W
R/W
R/W
1
0
1
0
1
0
PCINT24
PCINT16
PCINT8
R/W
R/W
R/W
0
0
0
0
0
0
PCMSK3
PCMSK2
PCMSK1
70