ATmega324PA Atmel Corporation, ATmega324PA Datasheet - Page 298

• Manufacturer Part Number: ATmega324PA
• Manufacturer: Atmel Corporation

Specifications of ATmega324PA

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.2
8272C–AVR–06/11
Fuse Bits
Table 27-2.
Notes:
The ATmega164A/164PA/324A/324PA/644A/644PA/1284/1284P has four Fuse bytes.
27-3
the Fuse bytes. Note that the fuses are read as logical zero, “0”, if they are programmed.
Table 27-3.
Note:
–
–
–
–
–
BODLEVEL2
BODLEVEL1
BODLEVEL0
BLB1 Mode
Fuse Low Byte
-
Table 27-5
1
2
3
4
1. Program the Fuse bits and Boot Lock bits before programming the LB1 and LB2.
2. “1” means unprogrammed, “0” means programmed
1. See
Memory Lock Bits
(1)
(1)
(1)
ATmega164A/PA/324A/PA/644A/PA/1284/P
Lock Bit Protection Modes
Extended Fuse Byte
”System and Reset Characteristics” on page 337
BLB12
describe briefly the functionality of all the fuses and how they are mapped into
1
1
0
0
7
6
5
4
3
2
1
0
Bit No
BLB11
1
0
0
1
Description
–
–
–
–
–
Brown-out Detector trigger level
Brown-out Detector trigger level
Brown-out Detector trigger level
Protection Type
No restrictions for SPM or (E)LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section, and
(E)LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
(E)LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
(1)(2)
(Continued)
for BODLEVEL Fuse decoding.
Default Value
1
1
1
1
1
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
Table
298