ATMEGA406-1AAU Atmel, ATMEGA406-1AAU Datasheet - Page 154

• Manufacturer Part Number: ATMEGA406-1AAU
• Description: IC AVR MCU 40K 1MHZ 48LQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA406-1AAU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 1MHz
• Connectivity: I²C
• Peripherals: POR, WDT
• Number Of I /o: 18
• Program Memory Size: 40KB (20K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 25 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -30°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: ATMEGA48x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire
• Maximum Clock Frequency: 1 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 30 C
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 1MHz
• Total Internal Ram Size: 2KB
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5/9/12/15/18/24V
• Operating Supply Voltage (max): 25V
• Operating Supply Voltage (min): 4V
• On-chip Adc: 10-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -30C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: AVR MEGA
• No. Of I/o's: 18
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 2KB
• Cpu Speed: 1MHz
• Rohs Compliant: Yes
• For Use With: 770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

25.8.1
154
ATmega406
Master Transmitter Mode
In
bers in the circles show the status code held in TWSR, with the prescaler bits masked to zero. At
these points, actions must be taken by the application to continue or complete the TWI transfer.
The TWI transfer is suspended until the TWINT flag is cleared by software.
When the TWINT flag is set, the status code in TWSR is used to determine the appropriate soft-
ware action. For each status code, the required software action and details of the following serial
transfer are given in
these tables.
In the Master Transmitter mode, a number of data bytes are transmitted to a slave receiver (see
Figure
mat of the following address packet determines whether Master Transmitter or Master Receiver
mode is to be entered. If SLA+W is transmitted, MT mode is entered, if SLA+R is transmitted,
MR mode is entered. All the status codes mentioned in this section assume that the prescaler
bits are zero or are masked to zero.
Figure 25-12. Data Transfer in Master Transmitter Mode
Figure 25-13
SDA
SCL
S:
Rs:
R:
W:
A:
A:
Data:
P:
SLA:
25-12). In order to enter a Master mode, a START condition must be transmitted. The for-
TRANSMITTER
Device 1
MASTER
to
Figure
Table 25-3
25-19, circles are used to indicate that the TWINT flag is set. The num-
Device 2
RECEIVER
SLAVE
START condition
REPEATED START condition
Read bit (high level at SDA)
Write bit (low level at SDA)
Acknowledge bit (low level at SDA)
Not acknowledge bit (high level at SDA)
8-bit data byte
STOP condition
Slave Address
to
Table
Device 3
25-6. Note that the prescaler bits are masked to zero in
........
Device n
V
BUS
R1
R2
2548E–AVR–07/06