ATMEGA406-1AAU Atmel, ATMEGA406-1AAU Datasheet - Page 61

• Manufacturer Part Number: ATMEGA406-1AAU
• Description: IC AVR MCU 40K 1MHZ 48LQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA406-1AAU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 1MHz
• Connectivity: I²C
• Peripherals: POR, WDT
• Number Of I /o: 18
• Program Memory Size: 40KB (20K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 25 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -30°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: ATMEGA48x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire
• Maximum Clock Frequency: 1 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 30 C
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 1MHz
• Total Internal Ram Size: 2KB
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5/9/12/15/18/24V
• Operating Supply Voltage (max): 25V
• Operating Supply Voltage (min): 4V
• On-chip Adc: 10-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -30C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: AVR MEGA
• No. Of I/o's: 18
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 2KB
• Cpu Speed: 1MHz
• Rohs Compliant: Yes
• For Use With: 770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13.2
13.2.1
2548E–AVR–07/06
Low Voltage Ports as General Digital I/O
Configuring the Pin
The low voltage ports are bi-directional I/O ports with optional internal pull-ups.
shows a functional description of one I/O-port pin, here generically called Pxn.
Figure 13-2. General Low Voltage Digital I/O
Note:
Each port pin consists of three register bits: DDxn, PORTxn, and PINxn. As shown in
Description” on page
at the PORTx I/O address, and the PINxn bits at the PINx I/O address.
The DDxn bit in the DDRx Register selects the direction of this pin. If DDxn is written logic one,
Pxn is configured as an output pin. If DDxn is written logic zero, Pxn is configured as an input
pin.
If PORTxn is written logic one when the pin is configured as an input pin, the pull-up resistor is
activated. To switch the pull-up resistor off, PORTxn has to be written logic zero or the pin has to
be configured as an output pin. The port pins are tri-stated when reset condition becomes active,
even if no clocks are running.
If PORTxn is written logic one when the pin is configured as an output pin, the port pin is driven
high (one). If PORTxn is written logic zero when the pin is configured as an output pin, the port
pin is driven low (zero).
1. WRx, WPx, WDx, RRx, RPx, and RDx are common to all pins within the same port. clk
Pxn
SLEEP, and PUD are common to all ports.
PUD:
SLEEP:
clk
I/O
73, the DDxn bits are accessed at the DDRx I/O address, the PORTxn bits
:
PULLUP DISABLE
SLEEP CONTROL
I/O CLOCK
SLEEP
(1)
SYNCHRONIZER
WDx:
RDx:
WRx:
RRx:
RPx:
D
L
WPx:
Q
Q
D
PINxn
WRITE DDRx
READ DDRx
WRITE PORTx
READ PORTx REGISTER
READ PORTx PIN
WRITE PINx REGISTER
Q
Q
RESET
RESET
PORTxn
Q
Q
Q
Q
DDxn
CLR
CLR
D
D
RRx
ATmega406
PUD
WDx
RDx
RPx
clk
1
0
I/O
WPx
WRx
Figure 13-2
”Register
I/O
,
61