ATMEGA406-1AAU Atmel, ATMEGA406-1AAU Datasheet - Page 206

• Manufacturer Part Number: ATMEGA406-1AAU
• Description: IC AVR MCU 40K 1MHZ 48LQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA406-1AAU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 1MHz
• Connectivity: I²C
• Peripherals: POR, WDT
• Number Of I /o: 18
• Program Memory Size: 40KB (20K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 25 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -30°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: ATMEGA48x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire
• Maximum Clock Frequency: 1 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 30 C
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 1MHz
• Total Internal Ram Size: 2KB
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5/9/12/15/18/24V
• Operating Supply Voltage (max): 25V
• Operating Supply Voltage (min): 4V
• On-chip Adc: 10-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -30C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: AVR MEGA
• No. Of I/o's: 18
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 2KB
• Cpu Speed: 1MHz
• Rohs Compliant: Yes
• For Use With: 770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

28.6.9
28.6.10
28.6.11
206
ATmega406
Programming the Fuse Low Bits
Programming the Fuse High Bits
Programming the Lock Bits
The algorithm for programming the Fuse Low bits is as follows (refer to
on page 202
1. A: Load Command “0100 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
3. Give WR a negative pulse and wait for RDY/BSY to go high.
The algorithm for programming the Fuse High bits is as follows (refer to
Flash” on page 202
1. A: Load Command “0100 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
3. Set BS1 to “1” and BS2 to “0”. This selects high data byte.
4. Give WR a negative pulse and wait for RDY/BSY to go high.
5. Set BS1 to “0”. This selects low data byte.
Figure 28-5. Programming the FUSES Waveforms
The algorithm for programming the Lock bits is as follows (refer to
page 202
1. A: Load Command “0010 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs the Lock bit. If LB mode 3 is programmed
3. Give WR a negative pulse and wait for RDY/BSY to go high.
The Lock bits can only be cleared by executing Chip Erase.
(LB1 and LB2 is programmed), it is not possible to program the Boot Lock bits by any
External Programming mode.
for details on Command and Data loading):
for details on Command and Data loading):
RESET +12V
for details on Command and Data loading):
RDY/BSY
PAGEL
XTAL1
DATA
XA1
XA0
BS1
BS2
WR
OE
0x40
A
DATA
C
Write Fuse Low byte
XX
0x40
A
DATA
C
Write Fuse high byte
XX
”Programming the Flash” on
”Programming the Flash”
”Programming the
2548E–AVR–07/06