ATMEGA406-1AAU Atmel, ATMEGA406-1AAU Datasheet - Page 205

• Manufacturer Part Number: ATMEGA406-1AAU
• Description: IC AVR MCU 40K 1MHZ 48LQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA406-1AAU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 1MHz
• Connectivity: I²C
• Peripherals: POR, WDT
• Number Of I /o: 18
• Program Memory Size: 40KB (20K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 25 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -30°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: ATMEGA48x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire
• Maximum Clock Frequency: 1 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 30 C
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 1MHz
• Total Internal Ram Size: 2KB
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5/9/12/15/18/24V
• Operating Supply Voltage (max): 25V
• Operating Supply Voltage (min): 4V
• On-chip Adc: 10-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -30C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: AVR MEGA
• No. Of I/o's: 18
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 2KB
• Cpu Speed: 1MHz
• Rohs Compliant: Yes
• For Use With: 770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

28.6.7
28.6.8
2548E–AVR–07/06
Reading the Flash
Reading the EEPROM
Figure 28-4. Programming the EEPROM Waveforms
The algorithm for reading the Flash memory is as follows (refer to
page 202
1. A: Load Command “0000 0010”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. Set OE to “0”, and BS1 to “0”. The Flash word low byte can now be read at DATA.
5. Set BS to “1”. The Flash word high byte can now be read at DATA.
6. Set OE to “1”.
The algorithm for reading the EEPROM memory is as follows (refer to
on page 202
1. A: Load Command “0000 0011”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. Set OE to “0”, and BS1 to “0”. The EEPROM Data byte can now be read at DATA.
5. Set OE to “1”.
RESET +12V
RDY/BSY
PAGEL
XTAL1
DATA
XA1
XA0
BS1
BS2
WR
OE
for details on Command and Address loading):
for details on Command and Address loading):
0x11
A
ADDR. HIGH
G
ADDR. LOW
B
DATA
C
XX
E
ADDR. LOW
B
DATA
C
K
XX
E
”Programming the Flash” on
”Programming the Flash”
L
ATmega406
205