ATMEGA406-1AAU Atmel, ATMEGA406-1AAU Datasheet - Page 207

• Manufacturer Part Number: ATMEGA406-1AAU
• Description: IC AVR MCU 40K 1MHZ 48LQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA406-1AAU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 1MHz
• Connectivity: I²C
• Peripherals: POR, WDT
• Number Of I /o: 18
• Program Memory Size: 40KB (20K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 25 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -30°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: ATMEGA48x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: 2-Wire
• Maximum Clock Frequency: 1 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 30 C
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 1MHz
• Total Internal Ram Size: 2KB
• # I/os (max): 18
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5/9/12/15/18/24V
• Operating Supply Voltage (max): 25V
• Operating Supply Voltage (min): 4V
• On-chip Adc: 10-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -30C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: AVR MEGA
• No. Of I/o's: 18
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 2KB
• Cpu Speed: 1MHz
• Rohs Compliant: Yes
• For Use With: 770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

28.6.12
28.6.13
28.6.14
2548E–AVR–07/06
Reading the Fuse and Lock Bits
Reading the Signature Bytes
Reading the Calibration Byte
The algorithm for reading the Fuse and Lock bits is as follows (refer to
on page 202
1. A: Load Command “0000 0100”.
2. Set OE to “0”, BS2 to “0” and BS1 to “0”. The status of the Fuse Low bits can now be
3. Set OE to “0”, BS2 to “1” and BS1 to “1”. The status of the Fuse High bits can now be
4. Set OE to “0”, BS2 to “0” and BS1 to “1”. The status of the Lock bits can now be read at
5. Set OE to “1”.
Figure 28-6. Mapping Between BS1, BS2 and the Fuse and Lock Bits During Read
The algorithm for reading the Signature bytes is as follows (refer to
page 202
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte (0x00 - 0x02).
3. Set OE to “0”, and BS to “0”. The selected Signature byte can now be read at DATA.
4. Set OE to “1”.
The algorithm for reading the Calibration byte is as follows (refer to
page 202
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte, 0x00.
3. Set OE to “0”, and BS1 to “1”. The Calibration byte can now be read at DATA.
4. Set OE to “1”.
read at DATA (“0” means programmed).
read at DATA (“0” means programmed).
DATA (“0” means programmed).
for details on Command and Address loading):
for details on Command and Address loading):
for details on Command loading):
Fuse High Byte
Fuse Low Byte
Lock Bits
0
BS2
BS2
0
1
0
1
BS1
0
1
”Programming the Flash” on
”Programming the Flash” on
”Programming the Flash”
DATA
ATmega406
207