AT91SAM7A3-AU Atmel, AT91SAM7A3-AU Datasheet - Page 330

• Manufacturer Part Number: AT91SAM7A3-AU
• Description: IC ARM7 MCU FLASH 256K 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7A3-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: CAN, I²C, MMC, SPI, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: AT91SAM7xx
• No. Of I/o's: 62
• Ram Memory Size: 32KB
• Cpu Speed: 60MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/SPI/I2S/TWI/USART/USB
• On-chip Adc: 2(8-chx10-bit)
• Number Of Timers: 3
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 60 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7A3-EK
• Minimum Operating Temperature: - 40 C
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 60MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7A3-EK - KIT EVAL FOR AT91SAM7A3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

30.6.8
30.6.9
330
AT91SAM7A3 Preliminary
Loop Mode
Interrupt
Figure 30-14. Transmit Frame Format in Continuous Mode
Note:
Figure 30-15. Receive Frame Format in Continuous Mode
Note:
The receiver can be programmed to receive transmissions from the transmitter. This is done
by setting the Loop Mode (LOOP) bit in SSC_RFMR. In this case, RD is connected to TD, RF
is connected to TF and RK is connected to TK.
Most bits in SSC_SR have a corresponding bit in interrupt management registers.
The SSC can be programmed to generate an interrupt when it detects an event. The interrupt
is controlled by writing SSC_IER (Interrupt Enable Register) and SSC_IDR (Interrupt Disable
Register) These registers enable and disable, respectively, the corresponding interrupt by set-
ting and clearing the corresponding bit in SSC_IMR (Interrupt Mask Register), which controls
the generation of interrupts by asserting the SSC interrupt line connected to the AIC.
1. STTDLY is set to 0. In this example, SSC_THR is loaded twice. FSDEN value has no effect
1. STTDLY is set to 0.
on the transmission. SyncData cannot be output in continuous mode.
TD
Start: 1. TXEMPTY set to 1
RD
2. Write into the SSC_THR
From SSC_THR
Start
DATLEN
Start = Enable Receiver
Data
To SSC_RHR
DATLEN
Data
From SSC_THR
DATLEN
Data
To SSC_RHR
DATLEN
Data
Default
6042E–ATARM–14-Dec-06