AT91SAM7A3-AU Atmel, AT91SAM7A3-AU Datasheet - Page 362

• Manufacturer Part Number: AT91SAM7A3-AU
• Description: IC ARM7 MCU FLASH 256K 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7A3-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: CAN, I²C, MMC, SPI, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: AT91SAM7xx
• No. Of I/o's: 62
• Ram Memory Size: 32KB
• Cpu Speed: 60MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/SPI/I2S/TWI/USART/USB
• On-chip Adc: 2(8-chx10-bit)
• Number Of Timers: 3
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 60 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7A3-EK
• Minimum Operating Temperature: - 40 C
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 60MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7A3-EK - KIT EVAL FOR AT91SAM7A3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

31.5.1.3
31.5.1.4
31.5.1.5
362
AT91SAM7A3 Preliminary
Clock Control
TC Operating Modes
Trigger
The clock of each counter can be controlled in two different ways: it can be enabled/disabled
and started/stopped. See
Figure 31-4. Clock Control
Each channel can independently operate in two different modes:
The TC Operating Mode is programmed with the WAVE bit in the TC Channel Mode Register.
In Capture Mode, TIOA and TIOB are configured as inputs.
In Waveform Mode, TIOA is always configured to be an output and TIOB is an output if it is not
selected to be the external trigger.
A trigger resets the counter and starts the counter clock. Three types of triggers are common
to both modes, and a fourth external trigger is available to each mode.
• The clock can be enabled or disabled by the user with the CLKEN and the CLKDIS
• The clock can also be started or stopped: a trigger (software, synchro, external or
• Capture Mode provides measurement on signals.
• Waveform Mode provides wave generation.
commands in the Control Register. In Capture Mode it can be disabled by an RB load event
if LDBDIS is set to 1 in TC_CMR. In Waveform Mode, it can be disabled by an RC Compare
event if CPCDIS is set to 1 in TC_CMR. When disabled, the start or the stop actions have
no effect: only a CLKEN command in the Control Register can re-enable the clock. When
the clock is enabled, the CLKSTA bit is set in the Status Register.
compare) always starts the clock. The clock can be stopped by an RB load event in
Capture Mode (LDBSTOP = 1 in TC_CMR) or a RC compare event in Waveform Mode
(CPCSTOP = 1 in TC_CMR). The start and the stop commands have effect only if the clock
is enabled.
Selected
Counter
Clock
Clock
Figure
Q
R
S
31-4.
Trigger
CLKSTA
Q
CLKEN
R
S
Event
Stop
CLKDIS
Disable
Event
6042E–ATARM–14-Dec-06