MC908AP64CFAE Freescale Semiconductor, MC908AP64CFAE Datasheet - Page 112

• Manufacturer Part Number: MC908AP64CFAE
• Description: IC MCU 64K 8MHZ SPI 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP64CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08AP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908AP64E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• Package: 48LQFP
• Family Name: HC08
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

System Integration Module (SIM)
7.7.1 SIM Break Status Register
The SIM break status register (SBSR) contains a flag to indicate that a break caused an exit from stop
mode or wait mode.
SBSW — Break Wait Bit
SBSW can be read within the break interrupt routine. The user can modify the return address on the stack
by subtracting 1 from it. The following code is an example.
112
This code works if the H register has been pushed onto the stack in the break
service routine software. This code should be executed at the end of the break
service routine software.
HIBYTE
LOBYTE
DOLO
RETURN
This status bit is set when a break interrupt causes an exit from wait mode or stop mode. Clear SBSW
by writing a logic 0 to it. Reset clears SBSW.
1 = Stop mode or wait mode was exited by break interrupt
0 = Stop mode or wait mode was not exited by break interrupt
Note: Writing a logic 0 clears SBSW.
EQU
EQU
If not SBSW, do RTI
BRCLR
TST
BNE
DEC
DEC
PULH
RTI
Address:
Reset:
Read:
Write:
$FE00
5
6
SBSW,SBSR, RETURN
LOBYTE,SP
DOLO
HIBYTE,SP
LOBYTE,SP
Bit 7
R
Figure 7-20. SIM Break Status Register (SBSR)
R
6
MC68HC908AP Family Data Sheet, Rev. 4
R
R
5
;
;
;If RETURNLO is not zero,
;then just decrement low byte.
;Else deal with high byte, too.
;Point to WAIT/STOP opcode.
;Restore H register.
= Reserved
See if wait mode or stop mode was exited by
break.
R
4
R
3
R
2
SBSW
Note
1
0
Freescale Semiconductor
Bit 0
R