MC908AP64CFAE Freescale Semiconductor, MC908AP64CFAE Datasheet - Page 212

• Manufacturer Part Number: MC908AP64CFAE
• Description: IC MCU 64K 8MHZ SPI 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP64CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08AP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908AP64E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• Package: 48LQFP
• Family Name: HC08
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Serial Peripheral Interface Module (SPI)
13.4 Functional Description
Figure 13-2
The SPI module allows full-duplex, synchronous, serial communication between the MCU and peripheral
devices, including other MCUs. Software can poll the SPI status flags or SPI operation can be
interrupt-driven.
The following paragraphs describe the operation of the SPI module.
13.4.1 Master Mode
The SPI operates in master mode when the SPI master bit, SPMSTR, is set.
Only a master SPI module can initiate transmissions. Software begins the transmission from a master SPI
module by writing to the transmit data register. If the shift register is empty, the byte immediately transfers
to the shift register, setting the SPI transmitter empty bit, SPTE. The byte begins shifting out on the MOSI
pin under the control of the serial clock. (See
The SPR1 and SPR0 bits control the baud rate generator and determine the speed of the shift register.
(See
master also controls the shift register of the slave peripheral.
As the byte shifts out on the MOSI pin of the master, another byte shifts in from the slave on the master’s
MISO pin. The transmission ends when the receiver full bit, SPRF, becomes set. At the same time that
SPRF becomes set, the byte from the slave transfers to the receive data register. In normal operation,
SPRF signals the end of a transmission. Software clears SPRF by reading the SPI status and control
register with SPRF set and then reading the SPI data register. Writing to the SPI data register clears the
SPTE bit.
210
$0010 SPI Control Register (SPCR)
$0011
$0012
Addr.
13.13.2 SPI Status and Control
SPI Status and Control
Register Name
shows the structure of the SPI module.
SPI Data Register
Configure the SPI modules as master or slave before enabling them.
Enable the master SPI before enabling the slave SPI. Disable the slave SPI
before disabling the master SPI. (See
(SPSCR)
Register
(SPDR)
Reset:
Reset:
Reset:
Read:
Read:
Read:
Write:
Write:
Write:
Figure 13-1. SPI I/O Register Summary
MC68HC908AP Family Data Sheet, Rev. 4
SPRIE
SPRF
Bit 7
R7
T7
0
0
Register.) Through the SPSCK pin, the baud rate generator of the
= Unimplemented
ERRIE
R6
T6
R
Figure
6
0
0
NOTE
SPMSTR
=
13-3.)
OVRF
13.13.1 SPI Control
R5
T5
5
1
0
MODF
Unaffected by reset
CPOL
R4
T4
4
0
0
CPHA
SPTE
R3
T3
R
3
1
1
Register.)
= Reserved
MODFEN
SPWOM
R2
T2
2
0
0
Freescale Semiconductor
SPR1
SPE
R1
T1
1
0
0
SPTIE
SPR0
Bit 0
R0
T0
0
0