MC908AP64CFAE Freescale Semiconductor, MC908AP64CFAE Datasheet - Page 227

• Manufacturer Part Number: MC908AP64CFAE
• Description: IC MCU 64K 8MHZ SPI 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AP64CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 32
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: HC08
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Controller Family/series: HC08
• No. Of I/o's: 32
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08AP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908AP64E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• Package: 48LQFP
• Family Name: HC08
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

SPWOM — SPI Wired-OR Mode Bit
SPE — SPI Enable
SPTIE— SPI Transmit Interrupt Enable
13.13.2 SPI Status and Control Register
The SPI status and control register contains flags to signal these conditions:
The SPI status and control register also contains bits that perform these functions:
SPRF — SPI Receiver Full Bit
Freescale Semiconductor
This read/write bit disables the pullup devices on pins SPSCK, MOSI, and MISO so that those pins
become open-drain outputs.
This read/write bit enables the SPI module. Clearing SPE causes a partial reset of the SPI. (See
Resetting the
This read/write bit enables CPU interrupt requests generated by the SPTE bit. SPTE is set when a byte
transfers from the transmit data register to the shift register. Reset clears the SPTIE bit.
•
•
•
•
•
•
•
This clearable, read-only flag is set each time a byte transfers from the shift register to the receive data
register. SPRF generates a CPU interrupt request if the SPRIE bit in the SPI control register is set also.
During an SPRF CPU interrupt, the CPU clears SPRF by reading the SPI status and control register
with SPRF set and then reading the SPI data register. Reset clears the SPRF bit.
1 = Wired-OR SPSCK, MOSI, and MISO pins
0 = Normal push-pull SPSCK, MOSI, and MISO pins
1 = SPI module enabled
0 = SPI module disabled
1 = SPTE CPU interrupt requests enabled
0 = SPTE CPU interrupt requests disabled
1 = Receive data register full
0 = Receive data register not full
Receive data register full
Failure to clear SPRF bit before next byte is received (overflow error)
Inconsistent logic level on SS pin (mode fault error)
Transmit data register empty
Enable error interrupts
Enable mode fault error detection
Select master SPI baud rate
Address
Reset:
Read:
Write:
SPI.) Reset clears the SPE bit.
Figure 13-14. SPI Status and Control Register (SPSCR)
$0011
SPRF
Bit 7
0
= Unimplemented
ERRIE
6
0
MC68HC908AP Family Data Sheet, Rev. 4
OVRF
5
0
MODF
4
0
SPTE
3
1
MODFEN
2
0
SPR1
1
0
SPR0
Bit 0
0
I/O Registers
13.9
225