AT91SAM9XE512-CU Atmel, AT91SAM9XE512-CU Datasheet - Page 210

• Manufacturer Part Number: AT91SAM9XE512-CU
• Description: MCU ARM9 512K FLASH 217-BGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9XE512-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 56K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Package: 217LFBGA
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 180 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 96
• Interface Type: EBI/Ethernet/SPI/TWI/USART/USB
• On-chip Adc: 4-chx10-bit
• Number Of Timers: 6
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 180 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM9XE-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9XE-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM9XE-EK - KIT EVAL FOR AT91SAM9XEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

23.8.6
23.8.7
210
AT91SAM9XE128/256/512 Preliminary
Reset Values of Timing Parameters
Usage Restriction
Table 23-8, “Register Mapping,”
The SMC does not check the validity of the user-programmed parameters. If the sum of SETUP
and PULSE parameters is larger than the corresponding CYCLE parameter, this leads to unpre-
dictable behavior of the SMC.
For read operations:
Null but positive setup and hold of address and NRD and/or NCS can not be guaranteed at the
memory interface because of the propagation delay of theses signals through external logic and
pads. If positive setup and hold values must be verified, then it is strictly recommended to pro-
gram non-null values so as to cover possible skews between address, NCS and NRD signals.
For write operations:
If a null hold value is programmed on NWE, the SMC can guarantee a positive hold of address,
byte select lines, and NCS signal after the rising edge of NWE. This is true for WRITE_MODE =
1 only. See
For read and write operations: a null value for pulse parameters is forbidden and may lead to
unpredictable behavior.
In read and write cycles, the setup and hold time parameters are defined in reference to the
address bus. For external devices that require setup and hold time between NCS and NRD sig-
nals (read), or between NCS and NWE signals (write), these setup and hold times must be
converted into setup and hold times in reference to the address bus.
“Early Read Wait State” on page
gives the default value of timing parameters at reset.
211.
6254C–ATARM–22-Jan-10