AT91SAM9XE512-CU Atmel, AT91SAM9XE512-CU Datasheet - Page 247

• Manufacturer Part Number: AT91SAM9XE512-CU
• Description: MCU ARM9 512K FLASH 217-BGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM9XE512-CU

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 56K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 217-LFBGA
• Package: 217LFBGA
• Device Core: ARM926EJ-S
• Family Name: 91S
• Maximum Speed: 180 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 96
• Interface Type: EBI/Ethernet/SPI/TWI/USART/USB
• On-chip Adc: 4-chx10-bit
• Number Of Timers: 6
• Processor Series: AT91SAMx
• Core: ARM926EJ-S
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 180 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM9XE-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM9XE-EK
• Minimum Operating Temperature: - 40 C
• For Use With: AT91SAM9XE-EK - KIT EVAL FOR AT91SAM9XEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

24.5.4
Figure 24-5. Refresh Cycle Followed by a Read Access
24.5.5
6254C–ATARM–22-Jan-10
SDRAMC_A[12:0]
D[31:0]
SDWE
(input)
SDCS
SDCK
RAS
CAS
SDRAM Controller Refresh Cycles
Power Management
Row n
col c col d
Dnb
Dnc
An auto-refresh command is used to refresh the SDRAM device. Refresh addresses are gener-
ated internally by the SDRAM device and incremented after each auto-refresh automatically.
The SDRAM Controller generates these auto-refresh commands periodically. An internal timer is
loaded with the value in the register SDRAMC_TR that indicates the number of clock cycles
between refresh cycles.
A refresh error interrupt is generated when the previous auto-refresh command did not perform.
It is acknowledged by reading the Interrupt Status Register (SDRAMC_ISR).
When the SDRAM Controller initiates a refresh of the SDRAM device, internal memory accesses
are not delayed. However, if the CPU tries to access the SDRAM, the slave indicates that the
device is busy and the master is held by a wait signal. See
Three low-power modes are available:
The SDRAM Controller activates one low-power mode as soon as the SDRAM device is not
selected. It is possible to delay the entry in self-refresh and power-down mode after the last
access by programming a timeout value in the Low Power Register.
Dnd
• Self-refresh Mode: The SDRAM executes its own Auto-refresh cycle without control of the
• Power-down Mode: Auto-refresh cycles are controlled by the SDRAM Controller. Between
• Deep Power-down Mode: (Only available with Mobile SDRAM) The SDRAM contents are
SDRAM Controller. Current drained by the SDRAM is very low.
auto-refresh cycles, the SDRAM is in power-down. Current drained in Power-down mode is
higher than in Self-refresh Mode.
lost, but the SDRAM does not drain any current.
t
RP
= 3
AT91SAM9XE128/256/512 Preliminary
t
RC
= 8
Figure
Row m
24-5.
t
RCD
= 3
col a
CAS = 2
Dma
247