P89LPC9341FDH,512 NXP Semiconductors, P89LPC9341FDH,512 Datasheet - Page 54

• Manufacturer Part Number: P89LPC9341FDH,512
• Description: IC 80C51 MCU FLASH 8K 28-TSSOP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC9341FDH,512

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 28-TSSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x8b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (8 bit, 4 Channel)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-1758 - BOARD EVAL FOR LPC93X MCU FAMILY
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935288632512

NXP Semiconductors
P89LPC9331_9341_9351_9361
Product data sheet
Fig 22. Watchdog timer in Watchdog mode (WDTE = 1)
watchdog
oscillator
(1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a feed
PCLK
sequence.
7.29.1 Software reset
7.29.2 Dual data pointers
0
1
7.28 Watchdog timer
7.29 Additional features
MOV WFEED1, #0A5H
MOV WFEED2, #05AH
oscillator
crystal
The watchdog timer causes a system reset when it underflows as a result of a failure to
feed the timer prior to the timer reaching its terminal count. It consists of a programmable
12-bit prescaler, and an 8-bit down counter. The down counter is decremented by a tap
taken from the prescaler. The clock source for the prescaler can be the PCLK, the nominal
400 kHz watchdog oscillator or low speed crystal oscillator. The watchdog timer can only
be reset by a power-on reset. When the watchdog feature is disabled, it can be used as
an interval timer and may generate an interrupt.
Watchdog mode. Feeding the watchdog requires a two-byte sequence. If PCLK is
selected as the watchdog clock and the CPU is powered down, the watchdog is disabled.
The watchdog timer has a time-out period that ranges from a few μs to a few seconds.
Please refer to the P89LPC9331/9341/9351/9361 User manual for more details.
The SRST bit in AUXR1 gives software the opportunity to reset the processor completely,
as if an external reset or watchdog reset had occurred. Care should be taken when writing
to AUXR1 to avoid accidental software resets.
The dual Data Pointers (DPTR) provides two different Data Pointers to specify the
address used with certain instructions. The DPS bit in the AUXR1 register selects one of
the two Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic 0 so that the DPS
bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1
register, without the possibility of inadvertently altering other bits in the register.
XTALWD
0
1
WDCON (A7H)
÷32
All information provided in this document is subject to legal disclaimers.
PRE2
Rev. 5 — 10 January 2011
PRESCALER
8-bit microcontroller with accelerated two-clock 80C51 core
PRE1
P89LPC9331/9341/9351/9361
PRE0
SHADOW REGISTER
-
Figure 22
-
8-BIT DOWN
WDL (C1H)
COUNTER
WDRUN
shows the watchdog timer in
WDTOF
© NXP B.V. 2011. All rights reserved.
WDCLK
002aae015
reset
54 of 94
(1)