UPD78F0890GK(A)-GAJ-AX NEC, UPD78F0890GK(A)-GAJ-AX Datasheet - Page 479
![8BIT MCU, 128K FLASH, 7K RAM, LQFP](/photos/19/1/190186/ge64lqfp05-40_sml.jpg)
UPD78F0890GK(A)-GAJ-AX
Manufacturer Part Number
UPD78F0890GK(A)-GAJ-AX
Description
8BIT MCU, 128K FLASH, 7K RAM, LQFP
Manufacturer
NEC
Datasheet
1.UPD78F0890GKA-GAJ-AX.pdf
(732 pages)
Specifications of UPD78F0890GK(A)-GAJ-AX
Controller Family/series
UPD78F
No. Of I/o's
55
Ram Memory Size
7KB
Cpu Speed
20MHz
No. Of Timers
10
No. Of Pwm
RoHS Compliant
Core Size
8bit
Program Memory Size
128KB
Oscillator Type
External, Internal
- Current page: 479 of 732
- Download datasheet (4Mb)
Internally, the local node recognizes that it has transmitted ACK. An overload frame cannot be transmitted to the CAN
bus.
16.13.2 Single-shot mode
CAN protocol, a message frame transmission that has been aborted by either arbitration loss or error occurrence has
to be repeated without control by software.). All other behavior of single shot mode is identical to normal operation
mode. Features of single shot mode can not be used in combination with normal mode with ABT.
setting of the AL bit of the C0CTRL register. When the AL bit is cleared to 0, re-transmission upon arbitration loss and
upon error occurrence is disabled. If the AL bit is set to 1, re-transmission upon error occurrence is disabled, but re-
transmission upon arbitration loss is enabled. As a consequence, the TRQ bit in a message buffer defined as a
transmit message buffer is cleared to 0 by the following events.
the C0INTS register respectively, and the type of the error can be identified by reading the LEC[2:0] bits of the C0LEC
register.
register is set to 1. If the CIE0 bit of the C0IE register is set to 1 at this time, an interrupt request signal is output.
Furthermore, ACK is not returned to the CAN bus in this mode upon the valid reception of a message frame.
In the single-shot mode, automatic re-transmission as defined in the CAN protocol is switched off (According to the
The single-shot mode disables the re-transmission of an aborted message frame transmission according to the
- Successful transmission of the message frame
- Arbitration loss while sending the message frame
- Error occurrence while sending the message frame
The events arbitration loss and error occurrence can be distinguished by checking the CINTS4 and CINTS3 bits of
Upon successful transmission of the message frame, the transmit completion interrupt bit CINTS0 of the C0INTS
The single-shot mode can be used when emulating time-triggered communication methods (e.g. TTCAN level 1).
Caution The AL bit is only valid in Single-shot mode. It does not influence the operation of re-
Caution If only two CAN nodes are connected to the CAN bus and one of them is operating in the
transmission upon arbitration loss in the other operation modes.
receive-only mode, there is no ACK on the CAN bus. Due to the missing ACK, the transmitting
node will transmit an active error flag, and repeat transmitting a message frame.
transmitting node becomes error passive after transmitting the message frame 16 times
(assuming that the error counter was 0 in the beginning and no other errors have occurred).
After the message frame for the 17th time is transmitted, the transmitting node generates a
passive error flag. The receiving node in the receive-only mode detects the first valid message
frame at this point, and the VALID bit is set to 1 for the first time.
CHAPTER 16 CAN CONTROLLER
User’s Manual U17554EJ4V0UD
479
The
Related parts for UPD78F0890GK(A)-GAJ-AX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![UPD70325L-8](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
![UPC1316C](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
![UPC393C](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
![UPA572T](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
![UPA672T](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
![UPA802T](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
![UPA803T](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
![UPA805T](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
![UPA807T](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
![UPA836TF](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
![UPC1676G](/images/manufacturer_photos/0/4/470/nec_tmb.jpg)
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: