TMPM330FWFG Toshiba, TMPM330FWFG Datasheet - Page 446
![no-image](/images/manufacturer_photos/0/6/668/toshiba_sml.jpg)
TMPM330FWFG
Manufacturer Part Number
TMPM330FWFG
Description
Microcontrollers (MCU) MCU w/ ARM Cortex-M3 128K FLASH, 8K SRAM
Manufacturer
Toshiba
Specifications of TMPM330FWFG
Processor Series
TX03
Core
ARM Cortex M3
3rd Party Development Tools
MDK-ARM, RL-ARM, ULINK2
Product Summaries
Summary
Lead Free
Yes
Rohs Compatible Product(s)
Available
Rom (kbytes)
128K
Rom Type
Flash
Ram (kbytes)
8K
Number Of Pins
100
Package
LQFP(14×14)
Vcc
3V
Cpu Mhz
40
Ssp (ch) Spi
-
I2c/sio (ch)
3
Uart/sio (ch)
3
Usb
-
Can
-
Ethernet
-
External Bus Interface
-
Cs/wait Controller (ch)
-
Dma Controller
-
10-bit Da Converter
-
10-bit Ad Converter
12
12-bit Ad Converter
-
16-bit Timer / Counter
10
Motor / Igbt Control
-
Real Time Clock
1
Watchdog Timer
Y
Osc Freq Detect
-
Clock Gear
Y
Low-power Hold Function
-
Remote Control Interface
Y
Hardware Cec Controller
Y
Comparators
-
Low-voltage Detector
-
Etm Hardware Trace
4-bit
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 446 of 528
- Download datasheet (6Mb)
17.2
Operation Mode
17.2
are the programmable modes. These two modes, the User Boot mode and the Single Boot mode, are referred to as
"Onboard Programming" modes where onboard rewriting of internal flash memory can be made on the user's card.
(PH0) pin while the device is in reset status.
This device has three operation modes including the mode not to use the internal flash memory.
Among the flash memory operation modes listed in the above table, the User Boot mode and the Single Boot mode
Either the Single Chip or Single Boot operation mode can be selected by externally setting the level of the BOOT
Operation Mode
Table 17-1 Operation Modes
Single chip mode
Single boot mode
Normal mode
User boot mode
Operation mode
Normal mode
Single chip mode
Table 17-2 Operation Mode Setting
Single chip mode
Single boot mode
User to set the
switch method
Figure 17-2 Mode Transition Diagram
Operation mode
After reset is cleared, it starts up from the internal flash memory.
In this operation mode, two different modes, i.e., the mode to execute user application
programs and the mode to rewrite the flash memory onboard the user’s card, are defined.
The former is referred to as "normal mode" and the latter "user boot mode.
The user can uniquely configure the system to switch between these two modes. For ex-
ample, the user can freely design the system such that the normal mode is selected when
the port "A0" is set to "1" and the user boot mode is selected when it is set to "0." The user
should prepare a routine as part of the application program to make the decision on the
selection of the modes.
After reset is cleared, it starts up from the internal Boot ROM (Mask ROM). In the Boot
ROM, an algorithm to enable flash memory rewriting on the user’s set through the serial
port of this device is programmed. By connecting to an external host computer through the
serial port, the internal flash memory can be programmed by transferring data in accordance
with predefined protocols.
boot mode
User
Page 426
RESET
0 → 1
0 → 1
Operation details
programming mode
Pin
Onboard
boot mode
BOOT (PH0)
Single
1
0
Reset state
TMPM330FDFG/FYFG/FWFG
Related parts for TMPM330FWFG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TMPM 10103](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
![TMPM 10105](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
![TMPM 10112](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
![TMPM 10115](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
![TMPM 10124](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet: