TMPM330FWFG Toshiba, TMPM330FWFG Datasheet - Page 478
![no-image](/images/manufacturer_photos/0/6/668/toshiba_sml.jpg)
TMPM330FWFG
Manufacturer Part Number
TMPM330FWFG
Description
Microcontrollers (MCU) MCU w/ ARM Cortex-M3 128K FLASH, 8K SRAM
Manufacturer
Toshiba
Specifications of TMPM330FWFG
Processor Series
TX03
Core
ARM Cortex M3
3rd Party Development Tools
MDK-ARM, RL-ARM, ULINK2
Product Summaries
Summary
Lead Free
Yes
Rohs Compatible Product(s)
Available
Rom (kbytes)
128K
Rom Type
Flash
Ram (kbytes)
8K
Number Of Pins
100
Package
LQFP(14×14)
Vcc
3V
Cpu Mhz
40
Ssp (ch) Spi
-
I2c/sio (ch)
3
Uart/sio (ch)
3
Usb
-
Can
-
Ethernet
-
External Bus Interface
-
Cs/wait Controller (ch)
-
Dma Controller
-
10-bit Da Converter
-
10-bit Ad Converter
12
12-bit Ad Converter
-
16-bit Timer / Counter
10
Motor / Igbt Control
-
Real Time Clock
1
Watchdog Timer
Y
Osc Freq Detect
-
Clock Gear
Y
Low-power Hold Function
-
Remote Control Interface
Y
Hardware Cec Controller
Y
Comparators
-
Low-voltage Detector
-
Etm Hardware Trace
4-bit
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 478 of 528
- Download datasheet (6Mb)
17.2
Operation Mode
17.2.10.6
nications between the controller and the target board, the controller must first send a value of 0x86 at a desired
baud rate to the target board. To use I/O Interface mode, the controller must send a value of 0x30 at 1/16 the
desired baud rate. Figure 17-4 shows the waveforms for the first byte.
reception disabled, and calculates the intervals of tAB, tAC and tAD. Figure 17-5 shows a flowchart describing
the steps to determine the intervals of tAB, tAC and tAD. As shown in the flowchart, the boot program captures
timer counts each time a logic transition occurs in the first serial byte. Consequently,the calculated tAB, tAC
and tAD intervals are bound to have slight errors. If the transfer goes at a high baud rate, the CPU might not
be able to keep up with the speed of logic transitions at the serial receive pin. In particular, I/O Interface mode
is more prone to this problem since its baud rate is generally much higher than that for UART mode. To avoid
such a situation, the controller should send the first serial byte at 1/16 the desired baud rate.
modes. If the length of tAB is equal to or less than the length of tCD, the serial operation mode is determined
as UART mode. If the length of tAB is greater than the length of tCD, the serial operation mode is determined
as I/O Interface mode. Bear in mind that if the baud rate is too high or the timer operating frequency is too
low, the timer resolution will be coarse, relative to the intervals between logic transitions. This becomes a
problem due to inherent errors caused by the way in which timer counts are captured by software; consequently
the boot program might not be able to determine the serial operation mode correctly. To prevent this problem,
reset UART mode within the programming routine.
mode is UART mode. To avoid such a situation, when UART mode is utilized, the controller should allow
for a time-out period within which it expects to receive an echo-back (0x86) from the target board. The
controller should give up the communication if it fails to get that echo-back within the allowed time. When
I/O Interface mode is utilized, once the first serial byte has been transmitted, the controller should send the
SCLK clock after a certain idle time to get an acknowledge response. If the received acknowledge response
is not 0x30, the controller should give up further communications.
greater than tCD as shown above. 0x91, 0xA1 or 0xB1 can be sent as the first byte code to determine the
falling edges of Point A and Point C and the rising edges of Point B and Point D. If tAB is greater than tCD
and SIO is selected by the resolution of the operation mode determination, the second byte code is 0x30 even
though the transmitted code on the first byte is not 0x30 (The first byte code to determine I/O interface mode
is described as 0x30).
I/O Interface
UART (0x86)
The first byte from the controller determines the serial operation mode. To use UART mode for commu-
After RESET is released, the boot program monitors the first serial byte from the controller, with the SIO
The flowchart in Figure 17-5 shows how the boot program distinguishes between UART and I/O Interface
For example, the serial operation mode may be determined to be I/O Interface mode when the intended
When the intended mode is I/O interface mode, the first byte does not have to be 0x30 as long as tAB is
(0x30)
Determination of a Serial Operation Mode
Point A
Point A
Figure 17-4 Serial Operation Mode Byte
Start
bit 0
tAB
bit 1
bit 0
Point B
tAB
bit 2
bit 1
Page 458
bit 3
bit 2
Point C
Point B
bit 4
bit 3
bit 5
bit 4
Point C
tCD
bit 6
bit 5
tCD
bit 7
bit 6
TMPM330FDFG/FYFG/FWFG
Point D
Point D
bit 7
Stop
Related parts for TMPM330FWFG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TMPM 10103](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
![TMPM 10105](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
![TMPM 10112](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
![TMPM 10115](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet:
![TMPM 10124](/photos/21/70/217080/4689924_tmb.jpg)
Part Number:
Description:
AC/DC Power Modules
Manufacturer:
TRACOPOWER
Datasheet: