LM3S102 Luminary Micro, Inc, LM3S102 Datasheet - Page 197
LM3S102
Manufacturer Part Number
LM3S102
Description
Lm3s102 Arm Microcontroller
Manufacturer
Luminary Micro, Inc
Datasheet
1.LM3S102.pdf
(330 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LM3S102-EQN20-C2
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S102-EQN20-C2T
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S102-IGZ-C2
Manufacturer:
TI
Quantity:
965
Company:
Part Number:
LM3S102-IQN20-C2
Manufacturer:
Texas Instruments
Quantity:
10 000
Company:
Part Number:
LM3S102-IQN20-C2T
Manufacturer:
Texas Instruments
Quantity:
10 000
- Current page: 197 of 330
- Download datasheet (3Mb)
11.2.6
11.3
July 6, 2006
All of the interrupt events are ORed together before being sent to the interrupt controller, so the
UART can only generate a single interrupt request to the controller at any given time. Software can
service multiple interrupt events in a single interrupt service routine by reading the UART Masked
Interrupt Status (UARTMIS) register (see page 215).
The interrupt events that can trigger a controller-level interrupt are defined in the UART Interrupt
Mask (UARTIM) register (see page 212) by setting the corresponding IM bit to 1. If interrupts are
not used, the raw interrupt status is always visible via the UART Raw Interrupt Status (UARTRIS)
register (see page 214).
Interrupts are always cleared (for both the UARTMIS and UARTRIS registers) by setting the
corresponding bit in the UART Interrupt Clear (UARTICR) register (see page 216).
Loopback Operation
The UART can be placed into an internal loopback mode for diagnostic or debug work. This is
accomplished by setting the LBE bit in the UARTCTL register (see page 210). In loopback mode,
data transmitted on U0Tx is received on the U0Rx input.
Initialization and Configuration
To use the UART, the peripheral clock must be enabled by setting the UART0 bit in the RCGC1
register.
This section discusses the steps that are required for using a UART module. For this example, the
system clock is assumed to be 20 MHz and the desired UART configuration is:
The first thing to consider when programming the UART is the baud-rate divisor (BRD), since the
UARTIBRD and UARTFBRD registers must be written before the UARTLCRH register. Using the
equation described in “Baud-Rate Generation” on page 195, the BRD can be calculated:
BRD = 20,000,000 / (16 * 115,200) = 10.8507
which means that the DIVINT field of the UARTIBRD register (see page 206) should be set to 10.
The value to be loaded into the UARTFBRD register (see page 207) is calculated by the equation:
UARTFBRD[DIVFRAC] = integer(0.8507 * 64 + 0.5) = 54
With the BRD values in hand, the UART configuration is written to the module in the following
order:
1.
2.
Receive Timeout
Transmit (when condition defined in the TXIFLSEL bit in the UARTIFLS register is met)
Receive (when condition defined in the RXIFLSEL bit in the UARTIFLS register is met)
115200 baud rate
Data length of 8 bits
One stop bit
No parity
FIFOs disabled
No interrupts
Disable the UART by clearing the UARTEN bit in the UARTCTL register.
Write the integer portion of the BRD to the UARTIBRD register.
Preliminary
LM3S102 Data Sheet
197
Related parts for LM3S102
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Lm3s1110 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1133 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1138 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1150 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1162 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1165 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1332 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1435 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1439 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1512 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1538 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1601 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1607 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Lm3s1608 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet: