MD2433-D8G-V3Q18-X-P SanDisk, MD2433-D8G-V3Q18-X-P Datasheet - Page 17

no-image

MD2433-D8G-V3Q18-X-P

Manufacturer Part Number
MD2433-D8G-V3Q18-X-P
Description
IC MDOC H1 8GB 115-FBGA
Manufacturer
SanDisk
Datasheet

Specifications of MD2433-D8G-V3Q18-X-P

Format - Memory
FLASH
Memory Type
FLASH - Nand
Memory Size
8G (1G x 8)
Speed
64ns
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-30°C ~ 85°C
Package / Case
115-LFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MD2433-D8G-V3Q18-X-P
Manufacturer:
SANDISK
Quantity:
18 120
Part Number:
MD2433-D8G-V3Q18-X-P
Manufacturer:
M-SYSTEM
Quantity:
363
Part Number:
MD2433-D8G-V3Q18-X-P
Manufacturer:
SanDisk
Quantity:
10 000
1.3.3
17
CE#
OE#
WE#
AVD#
ID0
LOCK#
BUSY#
RSTIN#
IRQ#
VCC
VCCQ
VSS
AD[15:12]
AD[11:8]
AD[7:4]
AD[3:0]
Signal
Signal Description
Table 2: Multiplexed Interface Signal Descriptions for mDOC H1 12x18 FBGA Package
D7, D8, D3, E2,
F7,G2, G3, G7,
E3, E8, F2, F3,
K8, H7, L7, J6,
J5, L4, H4, K3
J8, L8, J7, K7
L5, K4, J4, L3
Ball No.
K6, G4
H3, K9
G8
G9
D6
H9
E5
K5
F8
F5
J2
J3
Type
Input
PCI
OD
OD
ST
ST
ST
ST
ST
ST
ST
-
-
-
1,2
Multiplexed bus. Address and data signals.
Chip Enable, active low.
Write Enable, active low.
Output Enable, active low.
Set multiplexed interface.
Identification. Configuration control to support up to two
chips cascaded in the same memory window.
Chip 1 = ID0 = VSS, must be used for single-chip
configuration.
Chip 2 = ID0 = VCCQ
Lock, active low. When active, provides full hardware
data protection of selected partitions.
Open drain output held asserted until download process
has completed.
A 10 KΩ pull-up resistor is recommended even if this
signal is not used.
Reset, active low.
Open drain interrupt request output.
A 10 KΩ pull-up resistor is recommended even if this
signal is not used.
+3.3V supply for core logic. Requires a 10 nF and 0.1 µF
capacitor.
I/O power supply. Sets the logic 1 voltage level range of
I/O balls. VCCQ may be either 2.5V to 3.6V or 1.65V to
1.95V. Requires a 10 nF and 0.1 µF capacitor.
Ground. All VSS balls must be connected.
Data Sheet, Rev. 1.1
System Interface
Configuration
Control
Power
Description
mDOC H1 4Gb (512MByte) and 8Gb (1GByte)
95-DT-1104-01
Signal
Output
Output
Output
Supply
Supply
Supply
Input/
Type
Input
Input
Input
Input
Input
Input
Input

Related parts for MD2433-D8G-V3Q18-X-P