S9S12HY64J0MLH Freescale Semiconductor, S9S12HY64J0MLH Datasheet - Page 165

• Manufacturer Part Number: S9S12HY64J0MLH
• Description: MCU 64K FLASH AUTO 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12HY64J0MLH

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LCD, Motor control PWM, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-LQFP
• Controller Family/series: S12
• No. Of I/o's: 50
• Ram Memory Size: 4KB
• Cpu Speed: 64MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Processor Series: S12HY
• Core: HCS12
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12HY64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Register Global Address 0x3_FF06
Read: All modes through BDM operation when not secured
Write: All modes through BDM operation when not secured
Freescale Semiconductor
Special Single-Chip Mode
UNSEC
TRACE
Field
SDV
4
3
1
All Other Modes
Shift Data Valid — This bit is set and cleared by the BDM hardware. It is set after data has been transmitted as
part of a firmware or hardware read command or after data has been received as part of a firmware or hardware
write command. It is cleared when the next BDM command has been received or BDM is exited. SDV is used
by the standard BDM firmware to control program flow execution.
0 Data phase of command not complete
1 Data phase of command is complete
TRACE1 BDM Firmware Command is Being Executed — This bit gets set when a BDM TRACE1 firmware
command is first recognized. It will stay set until BDM firmware is exited by one of the following BDM commands:
GO or GO_UNTIL.
0 TRACE1 command is not being executed
1 TRACE1 command is being executed
Unsecure — If the device is secured this bit is only writable in special single chip mode from the BDM secure
firmware. It is in a zero state as secure mode is entered so that the secure BDM firmware lookup table is enabled
and put into the memory map overlapping the standard BDM firmware lookup table.
The secure BDM firmware lookup table verifies that the on-chip Flash is erased. This being the case, the UNSEC
bit is set and the BDM program jumps to the start of the standard BDM firmware lookup table and the secure
BDM firmware lookup table is turned off. If the erase test fails, the UNSEC bit will not be asserted.
0 System is in a secured mode.
1 System is in a unsecured mode.
Note: When UNSEC is set, security is off and the user can change the state of the secure bits in the on-chip
When BDM is made active, the CPU stores the content of its CCR register
in the BDMCCR register. However, out of special single-chip reset, the
BDMCCR is set to 0xD8 and not 0xD0 which is the reset value of the CCR
register in this CPU mode. Out of reset in all other modes the BDMCCR
register is read zero.
Reset
Flash EEPROM. Note that if the user does not change the state of the bits to “unsecured” mode, the
system will be secured again when it is next taken out of reset.After reset this bit has no meaning or effect
when the security byte in the Flash EEPROM is configured for unsecure mode.
W
R
CCR7
1
0
7
Table 5-2. BDMSTS Field Descriptions (continued)
Figure 5-4. BDM CCR Holding Register (BDMCCR)
MC9S12HY/HA-Family Reference Manual, Rev. 1.04
CCR6
1
0
6
CCR5
0
0
5
NOTE
Description
CCR4
0
0
4
CCR3
1
0
3
Background Debug Module (S12SBDMV1)
CCR2
0
0
2
CCR1
0
0
1
CCR0
0
0
0
165