M30626FJPFP#D5C Renesas Electronics America, M30626FJPFP#D5C Datasheet - Page 139

• Manufacturer Part Number: M30626FJPFP#D5C
• Description: MCU 3/5V 512K 100-QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30626FJPFP#D5C

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 24MHz
• Connectivity: I²C, IEBus, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 85
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 31K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

M16C/62P Group (M16C/62P, M16C/62PT)
Rev.2.41
REJ09B0185-0241
12.9
Table 12.6
Value of the PC that is saved to the stack area : Refer to 12.5.7 Saving Registers.
Table 12.7
• 16-bit op-code instruction
• Instruction shown below among 8-bit operation code instructions
Instructions other than the above
Address Match Interrupt 0
Address Match Interrupt 1
Address Match Interrupt 2
Address Match Interrupt 13
An address match interrupt is generated immediately before executing the instruction at the address indicated by
the RMADi register (i=0 to 3). Set the start address of any instruction in the RMADi register. Use the AIER0 and
AIER1 bits in the AIER register and AIER20 and AIER21 bits in the AIER2 register to enable or disable the
interrupt. Note that the address match interrupt is unaffected by the I flag and IPL. For address match interrupts, the
value of the PC that is saved to the stack area varies depending on the instruction being executed (refer to 12.5.7
Saving Registers).
(The value of the PC that is saved to the stack area is not the correct return address.) Therefore, follow one of the
methods described below to return from the address match interrupt.
Table 12.6 shows the Value of the PC that is Saved to the Stack Area when an Address Match Interrupt Request is
Accepted
Figure 12.13 shows the AIER, AIER2 and RMAD0 to RMAD3 Registers.
Address Match Interrupt sources
ADD.B:S
OR.B:S
STNZ.B:S
CMP.B:S
JMPS
MOV.B:S
•
•
Rewrite the content of the stack and then use the REIT instruction to return.
Restore the stack to its previous state before the interrupt request was accepted by using the POP or similar
other instruction and then use a jump instruction to return.
Address Match Interrupt
Jan 10, 2006
Request is Accepted
Value of the PC that is Saved to the Stack Area when an Address Match Interrupt
#IMM8,dest
#IMM8,dest
#IMM8,dest
#IMM8,dest
#IMM8
#IMM,dest (However, dest=A0 or A1)
Relationship Between Address Match Interrupt Sources and Associated Registers
Instruction at the Address Indicated by the RMADi Register
Page 122 of 390
SUB.B:S
MOV.B:S
STZX.B:S
PUSHM
JSRS
AIER0
AIER1
AIER20
AIER21
Address Match Interrupt Enable Bit
#IMM8,dest
#IMM8,dest
#IMM81,#IMM82,dest
src
#IMM8
AND.B:S
STZ.B:S
POPM dest
RMAD0
RMAD1
RMAD2
RMAD3
Address Match Interrupt Register
#IMM8,dest
#IMM8,dest
saved to the stack area
The address
indicated by the
RMADi register +2
The address
indicated by the
RMADi register +1
Value of the PC that is
12. Interrupt