PIC18F4520-I/P Microchip Technology Inc., PIC18F4520-I/P Datasheet - Page 172

• Manufacturer Part Number: PIC18F4520-I/P
• Description: 40 Pin, 32 KB Flash, 1536 RAM, 36 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F4520-I/P

• A/d Inputs: 13-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 36
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 32K Bytes
• Ram Size: 1.5K Bytes
• Speed: 40 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC18F2420/2520/4420/4520
17.4
The MSSP module in I
master and slave functions (including general call
support) and provides interrupts on Start and Stop bits
in hardware to determine a free bus (multi-master
function). The MSSP module implements the standard
mode specifications as well as 7-bit and 10-bit
addressing.
Two pins are used for data transfer:
• Serial clock (SCL) – RC3/SCK/SCL
• Serial data (SDA) – RC4/SDI/SDA
The user must configure these pins as inputs or outputs
through the TRISC<4:3> bits.
FIGURE 17-7:
DS39631A-page 170
RC3/SCK/SCL
RC4/SDI/
SDA
I
2
C Mode
Read
Shift
Clock
MSb
MSSP BLOCK DIAGRAM
(I
2
2
SSPADD reg
Match Detect
C mode fully implements all
C MODE)
Stop bit Detect
SSPBUF reg
SSPSR reg
Start and
LSb
Write
(SSPSTAT reg)
Internal
Data Bus
Addr Match
Set, Reset
S, P bits
Preliminary
17.4.1
The MSSP module has six registers for I
These are:
• MSSP Control Register 1 (SSPCON1)
• MSSP Control Register 2 (SSPCON2)
• MSSP Status Register (SSPSTAT)
• Serial Receive/Transmit Buffer Register
• MSSP Shift Register (SSPSR) – Not directly
• MSSP Address Register (SSPADD)
SSPCON1, SSPCON2 and SSPSTAT are the control
and status registers in I
SSPCON1 and SSPCON2 registers are readable and
writable. The lower 6 bits of the SSPSTAT are read-only.
The upper two bits of the SSPSTAT are read/write.
SSPSR is the shift register used for shifting data in or
out. SSPBUF is the buffer register to which data bytes
are written to or read from.
SSPADD register holds the slave device address when
the SSP is configured in I
SSP is configured in Master mode, the lower seven bits
of SSPADD act as the Baud Rate Generator reload
value.
In receive operations, SSPSR and SSPBUF together
create a double-buffered receiver. When SSPSR
receives a complete byte, it is transferred to SSPBUF
and the SSPIF interrupt is set.
During transmission, the SSPBUF is not double-
buffered. A write to SSPBUF will write to both SSPBUF
and SSPSR.
(SSPBUF)
accessible
REGISTERS
 2004 Microchip Technology Inc.
2
2
C Slave mode. When the
C mode operation. The
2
C operation.