PIC18F4520-I/P Microchip Technology Inc., PIC18F4520-I/P Datasheet - Page 77

• Manufacturer Part Number: PIC18F4520-I/P
• Description: 40 Pin, 32 KB Flash, 1536 RAM, 36 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC18F4520-I/P

• A/d Inputs: 13-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 10 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 36
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 32K Bytes
• Ram Size: 1.5K Bytes
• Speed: 40 MHz
• Timers: 1-8-bit, 3-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

REGISTER 6-1:
 2004 Microchip Technology Inc.
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
EECON1 REGISTER
bit 7
EEPGD: Flash Program or Data EEPROM Memory Select bit
1 = Access Flash program memory
0 = Access data EEPROM memory
CFGS: Flash Program/Data EEPROM or Configuration Select bit
1 = Access Configuration registers
0 = Access Flash program or data EEPROM memory
Unimplemented: Read as ‘0’
FREE: Flash Row Erase Enable bit
1 = Erase the program memory row addressed by TBLPTR on the next WR command
0 = Perform write only
WRERR: Flash Program/Data EEPROM Error Flag bit
1 = A write operation is prematurely terminated (any Reset during self-timed programming in
0 = The write operation completed
WREN: Flash Program/Data EEPROM Write Enable bit
1 = Allows write cycles to Flash program/data EEPROM
0 = Inhibits write cycles to Flash program/data EEPROM
WR: Write Control bit
1 = Initiates a data EEPROM erase/write cycle or a program memory erase cycle or write cycle.
0 = Write cycle to the EEPROM is complete
RD: Read Control bit
1 = Initiates an EEPROM read (Read takes one cycle. RD is cleared in hardware. The RD bit can
0 = Does not initiate an EEPROM read
Legend:
R = Readable bit
S = Bit can be set by software, but not cleared
-n = Value at POR
EEPGD
R/W-x
Note:
(cleared by completion of erase operation)
normal operation, or an improper write attempt)
(The operation is self-timed and the bit is cleared by hardware once write is complete.
The WR bit can only be set (not cleared) in software.)
only be set (not cleared) in software. RD bit cannot be set when EEPGD = 1 or CFGS = 1.)
When a WRERR occurs, the EEPGD and CFGS bits are not cleared.
This allows tracing of the error condition.
CFGS
R/W-x
PIC18F2420/2520/4420/4520
U-0
Preliminary
—
W = Writable bit
‘1’ = Bit is set
R/W-0
FREE
WRERR
R/W-x
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
WREN
R/W-0
x = Bit is unknown
R/S-0
WR
DS39631A-page 75
R/S-0
RD
bit 0