AT90PWM81-16SN Atmel, AT90PWM81-16SN Datasheet - Page 224

• Manufacturer Part Number: AT90PWM81-16SN
• Description: IC MCU AVR 8K FLASH ISP 20SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM81-16SN

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI
• Peripherals: Brown-out Detect/Reset, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 20-SOIC (7.5mm Width)
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 16 MHz
• Number Of Timers: 1
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Height: 2.35 mm
• Length: 13 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 7.6 mm
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

17.10 Amplifier Control Registers
17.10.1
224
AT90PWM81
Amplifier 0 Control and Status register – AMP0CSR
Figure 17-17. Amplifiers block diagram
If APMP0GS bit is set, the AMP0- input is open and PD5/AMP0- pin is free for another use. At the same
time the negative input of the Amplifier is internally grounded.
The configuration of the amplifier is controlled via the register AMP0CSR. Then the start of conversion is
done via the ADC control and status registers.
The conversion result is stored on ADCH and ADCL register which contain respectively the most signifi-
cant bits and the least significant bits.
Bit
Read/Write
Initial Value
• Bit 7 – AMP0EN: Amplifier 0 Enable Bit
Set this bit to enable the Amplifier 0.
Clear this bit to disable the Amplifier 0.
Clearing this bit while a conversion is running will take effect at the end of the conversion.
• Bit 6– AMP0IS: Amplifier 0 Input Shunt
Set this bit to short-circuit the Amplifier 0 input. If AMP0GS is set, the ground switch is released during
shunt of inputs.
Clear this bit to normally use the Amplifier 0.
AMP0+
AMP0-
7
AMP0EN
R/W
0
AMP0EN AMP0IS AMP0G1 AMP0G0
6
AMP0IS
R/W
0
no short
AMP0+ GND
Sampling
5
AMP0G1
R/W
0
Clock
4
AMP0G0
R/W
0
+
-
AMP0CSR
3
AMP0GS
-
0
00
01
10
1 1
AMP0GS
2
-
-
0
ADCK/8
PSCRASY
PSC2ASY
R/W
1
AMP0TS1
0
-
AMP0TS1 AMP0TS0
T oward ADC MUX
0
AMP0TS0
R/W
0
(AMP0)
7734P–AVR–08/10
AMP0CSR